Karcher HD 13/12-4 ST Manual
Summary of HD 13/12-4 ST
Page 1
Hd 7/16-4 st hd 7/16-4 st-h hd 9/18-4 st hd 9/18-4 st-h hd 13/12-4 st hd 13/12-4 st-h 59637700 08/14 deutsch 3 english 18 français 33 italiano 48 nederlands 63 español 78 português 93 dansk 108 norsk 123 svenska 138 suomi 153.
Page 2
- 1 please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent own- ers. Before first start-up it is definitely neces- sary to read the safety indications nr. 5.956-309.0! Notes about the ingredients (reach) you...
Page 3
- 2 if the operating time (without interruption of work) exceeds an adjustable value (5...120 minutes), the appliance will shut off. The motor protection switch switches off the device if the power consumption is high. In case of leaks in the high pressure sys- tem, the appliance is shut off. After ...
Page 4
- 3 1 solenoid valve water supply (upgrade kit, optional) 2 water inlet 3 swimmer valve 4 container of softener liquid with solenoid valve (4.1), only with mod- el st-h (option with model st) 5 prepressure pump, only with model st- h 6 high pressure pump 7 overflow valve 8 back up valve 9 pressure s...
Page 5
- 4 appliance cover removed. 1 oil tank 2 oil drain screw 3 power switch 4 electronics system 5 dosage valve for detergent 6 container of softener liquid (option) 7 float tank 8 hourmeter (option) 9 prepressure pump (model st-h only) 10 connectors for upgrade kits 11 water input (hd 7/16, hd 8/19) 1...
Page 6
- 5 note: the appliance is equipped with a pressure switch. The motor starts up only when the lever of the pistol is pulled open the water supply. Plug in the mains plug. (only with appliance versions with pow- er cable and mains plug). Set the appliance switch to "i". The indicator lamp glows green...
Page 7
- 6 you can sign with your dealer a contract for regular safety inspection or even sign a maintenance contract. Please take advice on this matter. Safety inspection/ maintenance contract maintenance schedule time activity assembly affected performance of whom daily check hand- spray gun hand spray g...
Page 8
- 7 in order to guarantee a reliable operation og the equipment, we success, you signed a maintenance agreement. Please refer to you local kärcher service department. Who may perform maintenance? Operator work designated with the sign “opera- tor” may only be carried out by persons who have been ins...
Page 9
- 8 fault possible cause remedy of whom water stream is uneven. Nozzle is blocked. Clean the nozzle. Operator amount of water supply is too low. Check water supply. Operator inadequate or no flow of de- tergent dosage adjusted too low. Increase dose. Operator nozzle is set to "high pressure". Set no...
Page 10
- 9 technical specifications hd 7/16-4 st hd 7/16-4 st-h hd 9/18-4 st hd 9/18-4 st-h hd 13/12-4 st hd 13/12-4 st-h electrical connection voltage v 400 230 440 220 400 230 440 220 400 230 440 220 current type -- 3~ 3~ 3~ frequency hz 50 60 50 60 50 60 connected load kw 5,0 6,8 7,3 electrical protecti...
Page 11
- 10 a water inlet 3/4" b high pressure output m 22x1.5 c electrical connection from the bottom d wall mount e on rack specifications sheet 27 en.
Page 12
- 11 detergents simplify the cleaning tasks. The table gives a selection of detergents. Please read the instructions on the packag- ing carefully before working with any deter- gents. The following types of detergent are not suitable because they damage the equipment. – cleaning agent containing nit...
Page 13
- 12 attachment sets remote controls 1 upgrade kit, remote re- lease* 2.637-491.0 1 operating point. Restoring the operation readiness after the readiness period has elapsed. Several operating stations can be used parallelly. 2 upgrade kit for remote con- trol, hd simple* 2.744-014.0 1 operating poi...
Page 14
- 13 – check the contents of the pack before unpacking. – in case of transport damage inform ven- dor immediately – store the drilling template on the carton to assemble the device. Note: the water connection, the high pressure network as well as the electrical connection can only be carried out by ...
Page 15
- 14 – using a hardness tester (order no. 6.768-004) danger dangerous electrical voltage! Setting may only be done by an electrician. Start the rotation potentiometer on the water softener board. The scale displays the hardening rang- es 1 to 4. Unscrew the nozzle. Switch on the appliance and let ...
Page 16
- 15 testing done on: findings: testing done on: findings: testing done on: findings: testing done on: findings: customer service plant type: manufact. No.: start-up on: signature signature signature signature 32 en.
Page 18
Http://www.Kaercher.Com/dealersearch.