KDK K15Z5 Operating And Installation Instructions - ■
7
4
Remove the Safety Wire Screw
f
from the Pipe.
Arrange and tie the Safety Wire
g
as shown.
• Firmly screw the Safety Wire
g
with
Safety Wire Screw
f
onto the Pipe.
WARNING
Ensure that the Ceiling
Hook can afford more than
10 times the Ceiling Fan
weight.
Do not remove the Insulock
Tie.
Safety Wire must be fi xed
correctly to the Pipe.
Can cause injury if the Ceiling
Fan drops.
4
Tanggalkan Skru Wayar
Keselamatan
f
dari Paip.
Susun dan ikat Wayar Keselamatan
g
seperti yang ditunjukkan.
• Ketatkan skru pada Wayar Keselamatan
g
dengan Skru Wayar Keselamatan
f
pada Paip.
AMARAN
Pastikan Cangkuk Siling
boleh menanggung beban
10 kali ganda berat Kipas
Siling.
Jangan tanggalkan
Pengikat Kabel.
Wayar Keselamatan mesti
dipasang dengan betul pada
Paip.
Boleh menyebabkan
kecederaan jika Kipas Siling
terjatuh.
4
从导管拆除保险线螺丝
f
。
如图所示排列及系绑保险线
g
。
• 以保险线螺丝
g
锁紧保险线
f
至
导管。
警告
确定天花板钩子可以承受超过
吊扇的
10
倍重量。
请勿拆除束带。
保险线必须正确地安装至导
管。
若吊扇掉落会导致受伤。
■
Install to ceiling
■
Memasang ke siling
■
安装至天花板
■
Note:
• In case “U” hook
d
is being used,
installation method is the same.
■
Nota:
• Walaupun cangkuk jenis “U”
d
digunakan, kaedah pemasangan masih
sama.
■
注意:
• 如果
“U”
形钩子
d
被使用,安装方法
是相同的。
Check point after installation
Make sure Bolt and Nut are fi rmly
tightened and Cotter Pin is inserted
and bent for safety reason.
The Ceiling Fan is securely fi xed onto
the Ceiling Hook.
Pemeriksaan selepas pemasangan
Untuk langkah keselamatan, pastikan
semua Bolt dan Nat diketatkan dan Cermat
Baji dimasukkan dan dibengkokkan.
Kipas Siling dipasang dalam keadaan
selamat pada Cangkuk Siling.
组装后的检验点
确保所有螺帽均已拧紧,且插入及拧
弯开口销以确保安全。
吊扇被稳固地安装到天花板钩子。
2
1
Remove the supplied Bolt
b
, Nut
c
, Cotter Pin
d
and Pulley
e
.
2
Place Pulley
e
on to the Ceiling
Hook
c
.
3
Firmly tighten the Bolt
b
, Nut
c
and Cotter Pin
d
.
• Cotter Pin
d
must fi x into Bolt
b
and bent.
1
Tanggalkan Bolt
b
, Nat
c
,
Cermat Baji
d
dan Takal
e
yang
dibekalkan.
2
Pasang Takal
e
pada Cangkuk
Siling
c
.
3
Ketatkan Bolt
b
, Nat
c
dan Cemat
Baji
d
.
• Cemat Baji
d
mesti dipasang pada
Bolt
b
dan dibengkokkan.
f
g
b
e
2
3
1
c
d
e
d
c
d
How to install
Cara pemasangan
如何安装
1
将配备的螺栓
b
、螺帽
c
、开口销
d
及滑轮
e
拆除。
2
将滑轮
e
置于天花板钩子
c
。
3
锁紧螺栓
b
、螺帽
c
及开口销
d
.
• 开口销
d
必须插入螺栓
b
然后
折弯。