- DL manuals
- KEDDY
- Stove
- K800 Series
- Installation Instructions Manual
KEDDY K800 Series Installation Instructions Manual
Summary of K800 Series
Page 1
K800 installation instructions care and firing instructions.
Page 2: Contents
Contents general information..................................................................................................3 important points..........................................................................................................3 prerequisites......................................
Page 3: General Information
General information thank you for choosing our wood burning stove! The k800 series has a number of unique characteristics, for example: * it is easy to install as it is in practice assembled on delivery * unique combustion system for greater safety and the best protection of the environment * modern...
Page 4: Prerequisites
Prerequisites building notice when you install a stove and erect a chimney, you may have to give building notice to the local planning and building committee. Contact the planning and building committee in your municipality for up-to- date information. Distance to flammable structural units before d...
Page 5: Preparations
Preparations 1. Floor plate and outdoor air connec- tion arrange the floor plate according to the instructions on page 4 under the heading floor plate. If you choose to make your own floor plate, the minimum dimensions stated in the above-mentioned point must be followed at all times. The illustrati...
Page 6
Example a rear connection directly into a chimneybreast or a masonry chimney, e.G. A heda chimney. Mark the centre for the hole in the wall for the flue. Check that the height agrees with the stove's connec- tion height. Make a hole with a diameter of approx. 180 mm using a drill and a chisel. Insta...
Page 7
1. When the outer packaging has been removed, the stove is screwed on a wooden pallet. Start by open- ing the door, by pressing up the handle on the bot- tom right. Take out the box with installation fittings. In the box, you will find an electric cable, a globe, base glass, a rear sleeve connection...
Page 8
5. Dismantle the top part. If the top is made of cast iron, the two rear screws must be removed, as shown in the illustration, before you can remove the top. If the top is made of concrete/stone, it only needs to be lifted straight up, since it located vertically against back plate in order to be ce...
Page 9: Installation Instructions
Installation instructions before starting on the installation of the stove, the following steps need to be fully completed: the chimney: alternative 1 an existing chimney prepared for rear connection alternative 2 a newly installed chimney prepared for rear connection alternative 3 preparation for a...
Page 10
We are now ready to place the stove in its intended position. 3. Put the bottom plate in place. Place the stove on the bottom plate and balance the stove verti- cally and horizontally using the four adjustment screws in each corner of the base. The adjust- ment screws must fit into the holes punched...
Page 11
7. If the chimney is to be installed on top, the chimney must be installed now. Connect the start module using sealant. Make sure that the joint is sealed by sticking your hand into the stove and spreading the sealant. Note! Always leave at least 5 mm of ven- tilated space between the top of the sto...
Page 12: Care & Firing Instructions
Care & firing instructions the k800 has been tested by the swedish national testing and research institute. It has met the strictest environmental requirements on the market and has useful efficiency of not less than 73%. For the k800 to work optimally, it is of key importance that you follow the ca...
Page 13
As the output modes are controlled automatically, the burning time for the wood loads mentioned above will be different. 3 - 4 kw approx. 60 - 80 minutes 6 - 7 kw approx. 50 - 60 minutes 8 - 9 kw approx. 40 for the automatic mode to work, the stove must have a power supply. If for some reason there ...
Page 14
- 14 - good to know since it can take some time for a cold chimney to start working properly, i.E. To force the smoke in the right direction, you can light a couple of sheets of news- paper and hold them up in front of the smoke shelf in the hearth. In this way, you eliminate the downdraught and avo...
Page 15: K800 Technical Specification
- 15 - k800 technical specification dimensions and performance height 1060 mm width 392.5 mm depth 400 mm weight k815 125 kg weight k825/835 135 kg height, centre rear connection 920 mm (if installed with floor glass) 926 mm height, top connection 1060 mm outer dimensions, connection sleeve Ø150 mm ...
Page 16
Www.Keddy.Se rev 5, 26/05/201 1.