Fastmig mf 29 operating manual käyttöohje bruksanvisning bruksanvisning brugsanvisning gebrauchsanweisung gebruiksaanwijzing manuel d’utilisation manual de instrucciones instrukcja obsługi Инструкции по эксплуатации manual de utilização manuale d’uso en fi sv no da de nl fr es pl ru pt it.
En operating manual english © kemppi oy / 1152.
En contents 1. Preface .......................................................................................... 3 1.1 general ....................................................................................................................................... 3 2. Product introduction .............
En 1. Preface 1.1 general congratulations on choosing the fastmig equipment. Used correctly, kemppi products can significantly increase the productivity of your welding, and provide years of economical service. This operating manual contains important information on the use, maintenance and safety o...
En 2. Product introduction fastmig mf is basic wire feeder designed for demanding enviroment. It can be used with kemppi's basic fastmig power sources km 300, km 400, and km 500. 2.1 operation control and connectors 1. 3. 4. 5. 6. 2. 1. Control panel 2. Welding gun euro connector 3. Connection for c...
En 2.2 connection of system 5 © kemppi oy / 1152.
En 2.3 duratorque™ 400, 4 wheel wire feed mechanism wire guide tubes ss, al, fe, mc, fc ø 0.6 ... 1.6 mm ø 2.5/64 mm, w000762, silver, plastic ø 2.5/33 mm, w000956, silver, plastic ø 2.0 mm, w000624, plastic ø 1.6 ... 2.4 mm ø 3.5/64 mm, w001430, silver, plastic ø 3.5/33 mm, w001431, silver, plastic...
En 3. Installation 3.1 assembly of mig system assemble the units in order mentioned below and follow mounting and operation instructions which are delivered in packages. Installation of power source read paragraph: ”installation” in operation instructions for fastmig power sources and carry out the ...
En • draw a bit of loose wire from wire spool. Feed wire through back liner to feed rolls. Do not release pressure of feed rolls! • press the gun switch and feed wire until wire goes through feed rolls to gun. See that wire is in grooves of both feed roll pairs! • press still the gun switch until wi...
En 3.9.1 installing gas cylinder note! Always fasten gas cylinder properly in vertical position in a special holder on the wall or on a carriage. Remember to close gas cylinder valve after having finished welding. Parts of gas flow regulator e b d g a f c a. Gas cylinder valve b. Press regulation sc...
En 3.11 operation of cooling unit, fastcool 10 operation of cooling unit is controlled in such a way that pump is started when welding is started. After welding stop pump is rotating for approx. 5 min cooling the gun and the cooling liquid to ambient temperature. Read in operation instructions for t...
En 5. Maintenance when considering and planning routine maintenance, please consider the the frequency of machine use and the working environment. Correct operation of the machine and regular maintenance will help you avoid unnecessary downtime and equipment failure. Note! Disconnect the machine fro...
En 6. Ordering numbers mf 29 6063200 km 300 3-ph 400v 6033000 km 400 3-ph 400v 6034000 km 500 3-ph 400v 6035000 cooling unit fastcool 10 6068100 transport unit pm500 6185291 accessories kwf 200 protection slides 6185286 kwf gas flow regulator (mounting set) w000364 mig-guns mmt 25 3 m 6252513mmt mmt...
En 7. Technical data mf 29 operating voltage (safety voltage) 24 vdc connection capacity 100 w output 40 °c 60 % ed 520 a 100 % ed 440 a wire feed mechanism 4-roll feed diameter of feed roll 32 mm wire feed speed 0 – 25 m/min filler wires ø fe, ss 0.6 – 1.6 mm ø cored wire 0.8 – 1.6 mm ø al 1.0 – 1....
Www.Kemppi.Com 1906320 1152 kemppi oy kempinkatu 1 pl 13 fin-15801 lahti finland tel +358 3 899 11 telefax +358 3 899 428 export@kemppi.Com www.Kemppi.Com kotimaan myynti: tel +358 3 899 11 telefax +358 3 734 8398 myynti.Fi@kemppi.Com kemppi sverige ab box 717 s-194 27 upplands vÄsby sverige tel +46...
