1. DL manuals
  2. Kurzweil
  3. Firewire
  4. KSP8 IO OPTION - REV E
  5. Installation Manual

Kurzweil KSP8 IO OPTION - REV E Installation Manual

Summary of KSP8 IO OPTION - REV E

  • Page 1

    Young chang co., ltd. 2003. Subject to change without notice. All trademarks are the properties of their respective owners. Part no. 910360, rev. E ksp8 i/o option installation and usage guide this document explains how to install an i/o option board into a kurzweil ksp8. The following i/o option bo...

  • Page 2

    Installation 2 figure 1. Rear view of ksp8, showing location of option slot cover plate. 3. Slide the i/o option board into the option slot as shown in figure 2. Make sure the side edges of the board slide into the plastic rails inside the option slot. Figure 2. Inserting option board into ksp8 (ana...

  • Page 3

    Using the ksp8 analog i/o option (kana4) 3 using the ksp8 analog i/o option (kana4) the analog i/o option adds four inputs and four outputs to your ksp8. The connectors are the same balanced 1/4" phone jacks that are used for the analog i/o on the stock ksp8, and their function is exactly the same. ...

  • Page 4: Studio Configuration Files

    Using the ksp8 adat–tdif i/o option (kadt8) 4 using the ksp8 adat–tdif i/o option (kadt8) the adat–tdif i/o option adds the following to your ksp8: • eight digital inputs and outputs for the adat optical interface. • eight digital inputs and outputs for devices that use the tdif format. Once you’ve ...

  • Page 5

    Using the ksp8 adat–tdif i/o option (kadt8) 5 806 mnin>5.1 autopan 807 3 sterin>5.1 fx+ 808 4 sterin>5.1 fx 809 5.1 in>5.1 fx + 810 default 5.1+ster 811 default 8 mono 812 default 4 stereo master table master page configuration parameters some adat or tdif configurations require that you set some of...

  • Page 6

    Using the ksp8 adat–tdif i/o option (kadt8) 6 configuration and connection examples the examples below show the most effective way to use your ksp8 in a variety of situations. Adat optical interface for this configuration, you should make the following selections on the ksp8 master and insel pages. ...

  • Page 7

    clocksource:tdi...

  • Page 8

    clocksource...

  • Page 11

    Using the ksp8 aes i/o option (kaes8) 11 using the ksp8 aes i/o option (kaes8) the aes i/o option adds four stereo input/output pairs to your ksp8. This option requires that the software revision level on your ksp8 be 1.7 or higher. The most current ksp8 software is provided on a smartmedia card inc...

  • Page 12: Studio Configuration Files

    Using the ksp8 aes i/o option (kaes8) 12 studio configuration files for your convenience, a configuration file named aesnn.Ksp is provided on the included smartmedia card. This file contains a subset of the base ksp8 studios with the appropriate input selections made, as well as a master table that ...

  • Page 13

    Using the ksp8 aes i/o option (kaes8) 13 pinout for aes/ebu connector the ksp8 aes option uses a single db-25 connector to provide four stereo input and output channels. While different manufacturers have used different standards in the pin assignments of these connectors for aes/ebu, the ksp8 emplo...

  • Page 14

    Using the ksp8 aes i/o option (kaes8) 14 cable requirements cables for connecting the ksp8 aes option should be constructed from shielded twisted-pair wiring with a nominal impedance of 110 ohms. The ground pins on each end of the cable connect to shields. The most common cable types are described b...

  • Page 15

    Using the ksp8 aes i/o option (kaes8) 15 • db-25 to db-25 aes cable (male-to-male) with ksp8-type pinouts this cable will have pinouts as shown in table 1 for connection to any device that uses the same aes pinout as the ksp8, for example, the panasonic da7 digital mixer. Since the pinout is the sam...

  • Page 16

    Using the ksp8 aes i/o option (kaes8) 16 • db-25 to db-25 aes cable (male-to-male) with ksp8-type pinout at one end and yamaha-type at other the yamaha-type connector uses the pinout shown in table 3 for attaching a device such as a yamaha 01v, 02r, or 03d digital mixer. Although this cable has db-2...

  • Page 17

    Using the ksp8 aes i/o option (kaes8) 17 cable sources • conquest sound – http://www.Conquestsound.Com/ • redco audio – http://www.Redco.Com/ • hosatech – http://www.Hosatech.Com • gig cables – http://www.Gigcables.Com/cndigital.Html also check the kurzweil web site (www.Kurzweilmusicsystems.Com) fo...

  • Page 18: Ksp8 Mlan I/o Option (Kmln8)

    Ksp8 mlan i/o option (kmln8) 18 ksp8 mlan i/o option (kmln8) the mlan i/o option adds firewire connectivity to your ksp8. This option requires that the software revision level on your ksp8 be 1.9 or higher. Complete documentation for the mlan i/o option is provided in a separate document (part numbe...