Land Pride Post Hole Diggers HD25 Operator's Manual - page 26
22
Section 3: Operating Instructions
HD25 and HD35 Hydraulic Post Hole Diggers 317-076M
7/31/17
8.
After penetrating the ground approximately 24", stop
auger rotation and raise it up to remove soil and
debris from the hole. Lower auger back down to
continue digging. Dig another 24" and again raise
auger up except this time keep auger turning to
lessen the strain on the equipment. Stop raising
auger within 1 to 2 feet of being out of the hole and
lower it back down to continue digging. Repeat this
procedure until hole is at its final depth.
9.
Allow auger to turn several revolutions at final depth.
With auger still turning, raise auger up to within 1 to 2
feet of being out of the hole. Stop auger rotation and
continue to raise auger out of the hole.
10. If connected to a front loader, roll tilt arms into a low
carry position; and if connected to a 3-point hitch,
raise auger fully up before transporting from one
digging site to the next. Be careful to watch out for
people, obstructions, and uneven terrain.
General Operation
By now you should have thoroughly read your Operator’s
Manual, properly installed your Post Hole Digger onto
your machine and performed your pre-start and
operational running checklist. If you plan to dig holes
immediately, you should have also contacted your local
utility companies to make sure it is safe to dig where you
plan to work. If you haven’t done all of the things just
described above, please stop and do them now. This is a
must for your safety and the safety of others.
Now that you are properly briefed, your Post Hole Digger
is properly installed, and you have the proper digging
authorization from the utility companies, it’s time to
transport to the work site. Make sure that the Post Hole
Digger is in the raised position and not in contact with the
ground. If you have an extensive distance to travel, you
may want to secure the auger with ropes, slings, or
chains to prevent swinging and damage during transport.
Select a safe speed and transport to your digging site in
such a manor that faster moving vehicles can pass you
safely. A slow moving vehicle sign should be employed if
you are using a public road or right-of-way.
Once you have safely arrived at your digging site,
position your tractor so that the auger is directly over the
spot where you want to dig a hole. Make sure your
operator protective shield or safety door is securely in
place. Lower auger to a point where the auger clears the
ground by approximately 12". Do not operate the digger
when the auger is more than 12" above ground level or
the auger could bind or swing erratically causing injury to
the operator and damage to the equipment.
IMPORTANT:Â
Some tractors have a hydraulic reliefÂ
valve to protect the equipment. This valve will openÂ
in a stalled situation and allow oil to bypass. CheckÂ
your tractor Operatorâs Manual to see if it isÂ
equipped with a relief valve.
With the engine at idle, engage hydraulic circuit and raiseÂ
engine RPM to operate at the recommended hydraulicÂ
flow to a point where the auger is turning at a speed ofÂ
approximately 85 to 100 RPM. (Refer toÂ
on page 34 for recommended hydraulicÂ
flow) Do not operate the auger at speeds over 110Â RPMÂ
or damage to the Post Hole Digger and skid steer/tractorÂ
could result. Using the controls, lower the auger into theÂ
ground until the desired depth is achieved and then raiseÂ
the spinning auger back up to remove extraneous soil.Â
Once the hole is completed, disengage hydraulic driveÂ
circuit, raise auger to a point where the auger tip isÂ
approximately 12" off of the ground, release the parkÂ
brake, and move away from the hole.
If an obstacle is encountered that stalls the auger,Â
reverse auger rotation and lift up to clear the obstacle.Â
Periodically adjust the machineâs position to keep theÂ
auger and hole vertical. Be careful not to damageÂ
gearbox or auger.
Before dismounting your tractor; you must always set theÂ
park brake, lower Auger to the ground, turn off theÂ
machine, and remove the ignition key. If you must park onÂ
a hillside, you should always chock the tractor wheels forÂ
an extra measure of safety.Â
With a little practice and experience you should becomeÂ
very good at operating your Land Pride HD25 or HD35Â
Series Post Hole Digger.Â
SeeÂ
âSpecifications & CapacitiesâÂ
on page 34 andÂ
âFeatures &Â Benefitsâ
 on page 37 for additionalÂ
information on performance enhancing options.