1. DL manuals
  2. Lasermate
  3. Office Equipment
  4. LM-5.5
  5. Operator's Manual

Lasermate LM-5.5 Operator's Manual

Manual is about: Pressure Seal Mailing System

Summary of LM-5.5

  • Page 1

    1 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual table of contents 1 introduction ..................................................................... 2 1.1 pictograms ................................................................2 1.2 notes on use of this handbook ..............

  • Page 2

    2 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 1. Introduction with this pressure sealer you have an advanced, medium-volume pressure sealing machine. Two sets of fold rollers provide secure sealing on all edges and its ease of operation makes it the ideal complement to the sma...

  • Page 3

    3 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 1.2 notes on the use of this handbook this document contains all general information and explanatory text necessary in order to be able to carry out the operation of the machine. When some action is expected from the operator, this...

  • Page 4

    4 lm-5.5 operator manual 2.1 general safety notes caution! Please, read these notes with care. Save these instructions for later use. All notes and warnings found on the machine are to be followed. Important! The machine must be installed on a suitably strong surface. The machine is very heavy and m...

  • Page 5: Important!

    Lm-5.5 operator manual 5 issue 5 january 2012 lm-5.5 operator manual spare parts when repair work is carried out, only original spare parts or spare parts corresponding to the original parts may be used. Repairs do not disassemble the machine any further than is described in this handbook. Other tha...

  • Page 6

    6 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 2.2 end of life the objectives of the european community’s environment policy are, in particular, to pre- serve, protect and improve the quality of the environment, protect human health and uti- lise natural resources prudently and...

  • Page 7

    7 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 3. Technical specification 3.1 machine rating sheet 1. Caution: in order to ensure correct safety and operation, this machine must only be installed and maintained by an authorized service engineer. 2. Caution: should any cover or ...

  • Page 8

    8 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 3.2 machine specifications form size: standard lengths: 11”, 11.69”, 12” & 14” standard widths: 8.27” & 8.5” fold types: standard v-fold: 8.5 x 11” standard c-fold: 8.5 x 11” standard z-fold: 8.5 x 11”, 8.5 x 14” eccentric z-fold: ...

  • Page 9

    9 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual physical dimensions: length: 23 ¾”, tray retracted 29 ¾”, tray extended width: 17.5” height: 18.5” to top of fold plate footprint: 15” long x 17.5” wide weight: 140lbs electrical: voltage: 115v @ 60hz current: 2.5a noise level: 75d...

  • Page 10

    10 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 4. Machine layout guide 4.1 description of machine the function of the lm-5.5 pressure sealer is to feed unfolded forms from a stack, fold them either once or twice, seal the cohesive edges and place them into a receiving tray. Fo...

  • Page 11

    11 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 5. Parts identification shown below are the main areas of the lm-5.5 pressure sealer. Fold plate 2 adjustor paper hopper fold plate 2 button for fold roller access fold plate 1 control panel receiving tray fold plate 1 adjustor em...

  • Page 12

    12 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 6. Control panel button/item description button/item function zero reset button: sets the forms count on the display to zero. (press again to restore count). Display: indicates forms count, error messages, assistance messages and ...

  • Page 13: Important!

    13 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 7. Operating overview shown below is an operating summary of the machine. Further details may be found in the section indicated. Action page 7.1 plug in the machine and switch on. 7.2 load paper into the paper hopper. 14 7.3 exten...

  • Page 14

    14 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 8. Set up 8.1 loading the paper hopper fan a stack of forms (max. 350) and align the edges. Press down on the tray and load the forms. Ensure the leading edges are fully contacting the chassis. Gently release the tray. Adjust the ...

  • Page 15

    15 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 8.2.2 fold plate 2 8.2.3 using v-folds if a single (v) fold is being used, the no-fold guide must be brought into position by use of a sliding knob inside the machine. See also section 8.2.4 for fold options. Loosen the knob and a...

  • Page 16

    16 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 8.2.4 fold options indicated below are the three types of folds that may be used. Use the arrow as a guide to which way the paper should be stacked on the tray; normally the address will be on the same side and at the same end as ...

  • Page 17

    17 lm-5.5 operator manual frequently used form sizes the list shown below indicates the fold plate settings for some typical folded forms. Notes: 1. F orms feed from top of stack b y friction. First fold is up the top fold plate. Second fold is down the bottom fold plate. There is no nesting feature...

  • Page 18

    18 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 9. Double document calibration each time the machine is run, it will automatically calibrate the first form to measure its size and thickness. Thereafter, if two forms are fed at the same time, they will be ejected through the slo...

  • Page 19

    19 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 11. Operator maintenance after a long period of use, dirt and toner can build up on the fold and seal rollers, and dust can cause the sensors to become obscured. This will need to be cleaned off to ensure reli- able operation. 11....

  • Page 20

    20 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual rear seal roller the rear seal roller is accessed by press- ing the button on top of the machine, then lowering the cover and hinging the inner chassis open. Clean the full width of the two rollers using the same fluid as the fold...

  • Page 21

    21 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 11.2 cleaning the sensors the optical sensors on the machine consists of two halves, spaced slightly apart. They should be cleaned at regular intervals using only a non-flammable airduster (part number 9103707c or equivalent), ens...

  • Page 22

    22 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 11.3 clearing paper jams if paper jams occur, they can usually be cleared by using the jog function or jam clearance lever. The jog function operates the machine in short spurts to drive out the jammed docu- ment in a controlled m...

  • Page 23

    23 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual cleaning rollers if you are using the jog function to clean rollers, it will be necessary to force a fault before the function will operate. To do this, simply remove all paper from the machine and press the run button - after a f...

  • Page 24

    24 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 12. Supervisor mode supervisor mode reveals various statistics about the machine, namely eprom version num- ber, total running hours and overall forms count. To enter the mode, press the stop button while the machine is displaying...

  • Page 25

    25 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual suggested cause and remedy 1. Ensure emergency stop button is not depressed and that power cord is plugged into power outlet. 2. Forms improperly loaded - ensure leading edges are firmly against chassis bridge and that the tray is...

  • Page 26

    26 lm-5.5 operator manual issue 5 january 2012 lm-5.5 operator manual 14. Error/status messages if operating faults occur, a code will appear on the control panel display, for example: the fault code will alternate with a scrolling description of the problem. If more than one fault has caused the ma...