- DL manuals
- Lectrosonics
- Transmitter
- SMDWB
- Instruction manual
Lectrosonics SMDWB Instruction manual
Summary of SMDWB
Page 1
Smwb series wireless microphone transmitters and recorders featuring digital hybrid wireless ® technology us patent 7,225,135 instruction manual rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date: smwb smdwb.
Page 2
Smwb series lectrosonics, inc. 2 consumer alert for us users - fcc order da 10-92 most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interfe...
Page 3
Digital hybrid wireless belt-pack transmitters rio rancho, nm 3 introduction the design of the smwb transmitter delivers the ad- vanced technology and features of digital hybrid wire- less ® in a lectrosonics belt-pack transmitter at a modest cost. Digital hybrid wireless ® combines a 24-bit digital...
Page 4
Smwb series lectrosonics, inc. 4 features battery status led indicator aa batteries can be used to power the transmitter. The led labeled batt on the keypad glows green when the batteries are good. The color changes to red when the battery voltage drops down and stays red through most of the battery...
Page 5
Digital hybrid wireless belt-pack transmitters rio rancho, nm 5 battery installation the transmitter is powered by two aa batteries. We recommend using lithium for longest life. Because some batteries run down quite abruptly, using the power led to verify battery status will not be reli- able. Howev...
Page 6
Smwb series lectrosonics, inc. 6 turning power on short button press when the unit is turned off, a short press of the power button will turn the unit on in the standby mode with the rf output turned off. A 494.500 -40 -20 0 e b 19 rf indicator blinks to turn the rf output on from the standby mode, ...
Page 7
Digital hybrid wireless belt-pack transmitters rio rancho, nm 7 transmitter operating instructions • install battery(s) • turn power on in the standby mode (see previous section) • connect microphone and place it in the position where it will be used. • have user talk or sing at the same level that ...
Page 8
Smwb series lectrosonics, inc. 8 smwb main menu freq. Rolloff compat stepsiz phase txpower sel back freq press sel to select desired adjustment use arrow keys to select desired frequency sel back sel back compat select from listing use arrow keys to select compatibility mode sel back use arrow keys ...
Page 9
Digital hybrid wireless belt-pack transmitters rio rancho, nm 9 smwb power button menu rf on? Battype remote press sel to return to the previous screen sel back use arrow keys to turn rf signal on/off no yes rf on? Sel back use arrow keys to choose battery type alk. Lith. Battype sel back use arrow ...
Page 10
Smwb series lectrosonics, inc. 10 setup screen details locking/unlocking changes to settings changes to the settings can be locked in the power button menu. Locked? No yes locked (menu to unlock) clock locked led off about when changes are locked, several controls and actions can still be used: • se...
Page 11
Digital hybrid wireless belt-pack transmitters rio rancho, nm 11 format files format record gain formats the microsdhc memory card. Warning: this function erases any content on the microsdhc memory card. Record or stop begins recording or stops recording. (see page 7.) adjusting the input gain the t...
Page 12
Smwb series lectrosonics, inc. 12 selecting frequency using two buttons hold the menu/sel button in, then use the and arrow buttons for alternate increments. Freq. B 19 494.500 51 1 block steps 1.6 mhz steps to nearest 100 khz channel 10 mhz steps 100 khz steps to next 100 khz channel 100 khz mode f...
Page 13
Digital hybrid wireless belt-pack transmitters rio rancho, nm 13 selecting step size this menu item allows frequencies to be selected in either 100 khz or 25 khz increments. Rolloff compat stepsiz phase stepsiz 100 khz 25 khz stepsiz 100 khz 25 khz if the desired frequency ends in .025, .050 or .075...
Page 14
Smwb series lectrosonics, inc. 14 the wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro- phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually impossible to...
Page 15
Digital hybrid wireless belt-pack transmitters rio rancho, nm 15 note: this termination is intended for uhf transmitters only. Vhf transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with vhf and uhf transmitters, which i...
Page 16
Smwb series lectrosonics, inc. 16 input jack wiring for different sources balanced and floating line level signals *note: if the output is balanced but center tapped to ground, such as on all lectrosonics receivers, do not connect pin 3 of the xlr jack to pin 4 of the ta5f connector. Ta5f plug xlr j...
Page 17
Digital hybrid wireless belt-pack transmitters rio rancho, nm 17 microphone rf bypassing when used on a wireless transmitter, the microphone element is in the proximity of the rf coming from the transmitter. The nature of electret microphones makes them sensitive to rf, which can cause problems with...
Page 18
Smwb series lectrosonics, inc. 18 firmware update firmware updates are made using a microsdhc memory card. Download and copy the following firm- ware update files to a drive on your computer. • smwb vx_xx.Ldr is the firmware update file, where “x_xx” is the revision number. In the computer: 1) perfo...
Page 19
Digital hybrid wireless belt-pack transmitters rio rancho, nm 19 recovery process in the event of a battery failure while the unit is re- cording, a recovery process is available to restore the recording in proper format. When a new battery is installed and the unit is turned back on, the recorder w...
Page 20
Smwb series lectrosonics, inc. 20 troubleshooting symptom: possible cause: transmitter battery led off 1. Batteries are inserted incorrectly. When power switch “on” 2. Batteries are low or dead. No transmitter modulation leds 1. Gain control turned all the way down. When signal should be present 2. ...
Page 21
Digital hybrid wireless belt-pack transmitters rio rancho, nm 21 transmitter operating frequencies: band a1: 470.100 - 537.575 band b1: 537.600 - 614.375 (608.000 to 614.000 excluded) band b2: 563.200 - 639.975 (608.000 to 614.000 excluded) band c1: 614.400 - 691.175 note: it’s the user’s responsibi...
Page 22
Smwb series lectrosonics, inc. 22 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and t...
Page 23
Digital hybrid wireless belt-pack transmitters rio rancho, nm 23.
Page 24: Limited One Year Warranty
581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com 06 december 2017 smwb_man.Indd limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or wor...