User guide lockwood keyless wireless digital deadbolt keyless wireless digital deadbolt lkddbw/sc - 0316.
3 table of contents warnings _______________________________________________________________________________________________4 introduction _____________________________________________________________________________________________4 installation _____________________________________________________...
4 the lockwood keyless wireless digital deadbolt lock combines a robust lockset with a contemporary electronic aesthetic. Users benefit from a touch keypad that makes day-to-day access effortless. Up to two hundred and fifty codes can be distributed amongst users to allow a keyless solution for acce...
5 inside escutcheon 4 aa alkaline batteries (2) through bolts bolt strike plate (4) bolt & strike plate mounting screws (3) inside escutcheon mounting screws inside mounting plate with gasket (back of inside escutcheon) battery cover outside escutcheon door preparation lock installation • 54mm hole ...
6 battery cover inside escutcheon inside escutcheon & mounting plate (with gasket) outside escutcheon 1 2 3 figure 3b figure 3a b. Bolt note: bolt ships with backset in 60mm position. If required, press small black button on underside of bolt and pull to extend to 70mm backset position (fig. 3b). Th...
7 figure 3a (2) m4 x 25.4mm [8-32 x 1"] flat head combination screws (2) m4 x 25.4mm [8-32 x 1”] flat head combination screws 1 2 figure 4a “tongue” inside of door figure 4b figure 3b 3. Install outside escutcheon. As you position the outside escutcheon, route the cable through 54mm diameter hole (f...
8 figure 6b figure 7 figure 6a figure 9 figure 8 caution: use care when assembling to ensure that the cable lies against the back recessed area of the inside escutcheon (fig. 6a). Position and bend cable, using the harness clips as shown in fig. 6a to prevent binding when installing the escutcheon o...
9 phillips head screw alkaline batteries 4 aa type thumbturn status indicator battery cover speaker hole lockout mode low battery indicator numbers touchscreen p key (return to previous) privacy mode button programming programming features-menus-keys-definitions _____________________________________...
10 low battery warning all code lockout mode return to previous step definitions components and tools master pin code: the master pin code is used for programming and for feature settings. It must be registered prior to programming the lock. The master code will also operate (unlock/lock) the lock (...
11 operation step 1 touch the screen with the back of your hand or fingers to activate. Step 2 press the key. Lock response: “register master code; press the # key to continue.” step 3 press the key. Lock response: “enter a 4 to 8 digit pin code followed by the pound key.” step 4 enter a new 4-8 dig...
12 press the key to confirm selection. Enter pin code. Touch lock with back of hand or fingers to activate. Open door with pin code 2 1 3 set up user codes protect your privacy; always shield your pin code entry. User pin codes can only be programmed through the master pin code*. 1. Touch the screen...
13 feature programming through menu mode using master pin code 1. Enter the 4-8 digit master pin code followed by the key. 2. Enter digit corresponding to the function to be performed followed by the key. Language setting mode **network module setting volume setting all code lockout mode **this func...
14 miscellaneous t 1 2 **network module setting pairing with z-wave/zigbee controllers _______________________________________________14 hardware troubleshooting _________________________________________________________16 programming troubleshooting __________________________________________________...
15 3. Pairing a z-wave/zigbee controller repeat step a. The digital deadbolt will show the option below. Note: (if the lockwood wireless digital deadbolt continues showing b, “exit the network” the digital deadbolt is still paired with the controller and steps a and b need to be repeated again) this...
16 cycle the lock in both the locked and the unlocked positions. If problems are found: troubleshooting hardware troubleshooting symptom suggested action door is binding a. Check that door and frame are properly aligned and door is free swinging. B. Check hinges: they should not be loose or have exc...
17 programming troubleshooting symptom suggested action lock does not respond - door is open and accessible. • press each keypad button to see if they respond when pressed. • check batteries are installed and oriented correctly in the battery case. • check batteries are in good condition; replace ba...
18 reset lock to factory default factory default settings cable reset button inside escutcheon to reset the lock to factory default, see the following: the following procedure returns the lock to its factory defaults by deleting all user codes (including the master pin code) and returning all progra...
19 installing/removing the network module important: the batteries must be removed prior to removing and/or inserting the network module: • remove battery cover • remove batteries • remove and/or insert network module • reinstall batteries use feature programming step 7 (page 13) for enrollment of t...
20 pin code management sample sheet pin code management (up to 20 users) location: door number: user type user name pin code user type user name pin code master user 01 user 11 user 02 user 12 user 03 user 13 user 04 user 14 user 05 user 15 user 06 user 16 user 07 user 17 user 08 user 18 user 09 use...
Assa abloy is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience lockwood is the leading brand in the australian locking industry. With an established reputation for high quality products, this iconic brand provides a wide range o...