Summary of TRM120
Page 1
1 wm1-trm120 trm120 trm – rotary mowers operators manual.
Page 2
2 trm120 serial number: date of purchase: section: description page 1 introduction 3 hse information sheet 4 - 7 2 in the interest of safety: do not 8 3 in the interest of safety: do 9 4 instruction & warning decals 10 5 transporting and lifting 11 6 operating principles 11 7 settings and adjustment...
Page 3
3 with the purchase of your logic trm - rotary mower you have made an excellent choice. This machine should give first class service for a long time, if used correctly, and maintained as described in this manual. Fitted with an easy to start engine it has been designed to cope with a wide range of c...
Page 4
4.
Page 5
5.
Page 6
6.
Page 7
7.
Page 8
8 1. Do not – operate the mower without all the correct guards fitted. 2. Do not - tamper with engine unless stated by engine manufacturer. 3. Do not – touch any moving or rotating parts during working conditions 4. Do not – stop the engine immediately after heavy use, ensure engine is run at idle f...
Page 9
9 1. Do – follow engine manufactures guidelines. 2. Do – ensure all spectators are a safe distance away when operating. 3. Do – carry out regular servicing and checks before use. 4. Do – clear cutting area from potential damaging components e.G. Stones etc. 5. Do – reduce speeds when working on hill...
Page 10
10 instruction / warning decals 4 the above decals should be located on your trm120. If any of the above decals are not located on your trm120 or are damaged in any way contact logic for some replacement decals before use..
Page 11
11 ensure the vehicle used to lift and transport the trm120 has the necessary lifting and loading capacity. Follow all vehicle manufactures guidelines for lifting. Unladen weights are clearly marked on the manufactures plate attached to the trm120 deck. Check the lifting weight complies with the veh...
Page 12
12 7.1 – before use inspection: ensure that all nuts, bolts and fittings are secure before using the trm120. Ensure the tyres are in good condition and have the correct pressures. Ensure the swivel hitch is in good condition; replace any worn or damaged parts. 7.2 – attachment to towing vehicle any ...
Page 13
13 quick offset drawbar remove the ‘r’ clip and locking pin; slide the drawbar to the desired position and reposition the locking pin into the securing hole as shown below. There are 4 hole positions as shown below that allow the mower to move to an ‘off set’ position. Hole position 1 (zero offset) ...
Page 14
14 starting the engine read and understand the engine operators manual before use observe all safety precautions; keep hands and feet away from the rotor and other moving parts. Keep spectators at a safe distance 1. Make sure there is a gap between the blades and the ground / crop 2. Select an area ...
Page 15
15 throttle park the mower deck is fitted with a throttle park. To use the throttle park clip the throttle to the bracket as shown below. Do not use the throttle park during operation. The throttle should be positioned near the operator during working conditions. Throttle park is for storage when th...
Page 16
16 all servicing should be carried out by qualified mechanics. Contact your local dealer for more details. Maintenance 8 maintenance schedule maintenance operation: hourly daily weekly seasonal engine (see engine manufacturer’s manual) see engine manufactures manual remove excess crop gathered on de...
Page 17
17 engine maintenance refer to engine manufacturer’s manual, for servicing and maintenance of the engine. Excess crop build up remove all crop deposits from the deck and engine area. Build up of crop deposits could result in heat build and fires. Nb: disconnect the spark plug lead. Remove any crop t...
Page 18
18 tyre / pressures do not exceed recommended tyre pressures 1. Remember that temperature affects pressures: in cold weather the pressure needs to be higher than in hotter temperatures. 2. Never adjust the pressure immediately after driving because driving heats up the tyres. There are many individu...
Page 19
19 wheel bearing inspection jack one side of the mower body up, so the wheel is just off the ground. Rotate the wheel by hand, and check the wheel alignment. To check the bearings, try to move the wheel from left to right and feel for any play in the bearings (a), ensure the wheel-locating bolt is t...
Page 20
20 3. Remove the blade bolt (b) 4. Remove the blade, replace or sharpen the blade. 5. Reinstall the blade ensure the blade-securing bolt has a torque setting of 60ft/lbs. 6. Inspect any fasteners before re-assembly, replace if necessary. 7. Reconnect spark plug. Specifications trm120b12*** trm120h13...
Page 21
21 9: parts diagram.
Page 22
22 item part number description 01 trm120-01a mower deck 02 trm120-14 rear deflector flap 03 frp06014 rivet mono 6.5mm x 14mm (2mm x 9.5mm panel) 04 fsh12035 s/screw hex head m12 x 35 05 trm120-09l rear discharge deflector l/h 05 trm120-09r rear discharge deflector r/h 06 trm120-22 rear clamping pla...
Page 23
23 item part number description 43 wt210 wl/ty 20 x 700 – 8 carlisle/max 4 44 mf120-1063 spacer 45 trm120-20a guard rail 46 fsh08030,fwf08,fnn08 s/screw m8 x 30, flat washers, nyloc nut 47 trm120-37 spring tension 5.38 mm dia 48 trm120-25la axle l/h 48 trm120-25ra axle r/h 49 trm120-10 wheel arm loc...
Page 24
24 this logic manufacturing product is guaranteed against faulty workmanship and materials for a period of 6 months from the date of purchase. On engine-powered equipment, the engine manufacturer’s guarantee will apply, any claims being subject to their terms and conditions. All claims must be made ...
Page 25
25 declaration of conformity declaration of conformity declaration of conformity declaration of conformity 93 / 44 eec 93 / 44 eec 93 / 44 eec 93 / 44 eec logic manufacturing ltd foundry industrial estate bridge end hexham northumberland product type: trm120 – rotary mower range covered by technical...