Magenta MultiView II DVI-Rx-1K Quick Start Manual - page 3
© 2014 tvONE, 2791 Circleport Drive, Erlanger KY 41018 USA
Americas: 859-282-7303, EMEA: +44 (0)1843 873322, email:
tech.usa@tvone.com
www.tvone.com
Document # CSG-MULTIVIEW-RX Rev-08 (09-Mar-2015)
Page 3 of 3
Configuration Mode, 4
th
Pair Options: The MVII-DVI-Rx-1K provides several options for using the 4
th
-pair signals (pairs 1-3 are
generally used for video). The factory-default settings support analog audio (L+R summed) on the 4
th
-pair. Note that the connected
MultiView transmitter and any daisy-chained receivers must be configured with a matching 4
th
-pair operating mode. Otherwise, the
desired 4
th
-pair signal will not work as expected
– but the video will not be affected. Note: If the optional SAP daughterboard is installed
then the 4
th
-pair options are fixed and unchangeable.
(starting in normal-mode)
Press & hold the CFG button until the CFG indictor is ON. Release the CFG button.
o
LEDs 1-8 will show the current value for all configuration settings as bright/off.
Press & release the SKEW/SEL button.
LED indicators 1-3 should be illuminated (either DIM or ON); all others (indicators 4-8) should be off.
Press the UP or DOWN buttons to step through the available 4
th
-pair settings as shown below.
To leave configuration-mode, leave the buttons untouched for 10 seconds or press the CFG button.
LED1
LED2
LED3
Front Panel View
4
th
-pair Operating Mode
dim
dim
dim
If option-module is installed: 4
th
-pair operating mode is defined by the presence
of the option-module (SAP) and this setting cannot be changed.
If the option-module is not installed: 4
th
-
pair signals are disabled. This “mutes”
anything being sent on the 4
th
pair. This can be useful for diagnostic purposes.
dim
dim
ON
Direct pass-through of 4
th
-pair wires (custom applications).
dim
ON
dim
External analog (L+R summed) audio
(“-A” mode).
This is the factory-default mode if no daughterboard option is installed.
(Remember to also check 4
th
-pair termination setting)
dim
ON
ON
External S/PDIF digital audio. Output-impedance = 75-ohms.
(Remember to also check 4
th
-pair termination setting)
ON
dim
dim
Simplex-serial
(“-S” mode)
(Remember to also check 4
th
-pair termination setting)
Configuration Mode, 4th Pair Termination: The MVII-DVI-Rx-1K provides settings for 4
th
pair termination: ON or OFF. This setting
has an effect only for “-S”, “-A” and S/PDIF operating modes. Note: It is not possible to access the 4
th
-pair setting if an option board is
installed
– since this setting is ignored.
Set to ON for all single-receiver applications, and for the last receiver in a daisy-chained configuration.
o
This is the factory-default.
Set to OFF only for mid-span receivers in a daisy-chain configuration.
(starting in normal-mode)
Press and hold the CFG button until the CFG indictor is ON.
o LEDs 1-8 will show the current value for all configuration settings as bright/off.
Press and release the SKEW/SEL button twice.
LED indicator 4 should be illuminated (either DIM or ON); all others (indicators 1-3 and 5-8) should be off.
Press the UP or DOWN buttons to turn 4
th
-pair termination ON (bright) or OFF (dim).
To leave configuration-mode, leave the buttons untouched for 10 seconds or press the CFG button.
To reset all user-configurable options back to factory-default settings:
Disconnect the DC power cable (or AC power).
Press and hold the CFG button.
Connect the DC power cable (or AC power). All LEDs will blink 3 times
– all settings are now changed back to factory-defaults.
Release the CFG button.
Troubleshooting: In many cases, problems encountered when installing
MultiView™II extension products can be resolved by checking
the F/UTP cable termination. It must be pinned out according to the TIA/EIA 568B standard wiring specification. For additional
troubleshooting information or to obtain the TIA/EIA 568B wiring specifications please refer to the MVII-DVI-Rx-1K User Guide,
downloadable from
http://www.tvone.com/