Summary of MONOSTICK 200 PFC
Page 1
Www.Oerlikon.Com.Tr monostick 200 pfc İ.
Page 2
İÇİndekİler safety rules 1. Technical information 1.1 general explanations 1.2 components of the machine 1.3 data plate 1.4 technical specifications 1.5 accessorries 2. Installation and operation 2.1 upon receipt and claims 2.2 installing and working recommendations 2.3 connections for mma welding 2...
Page 3
2 monostick 200i pfc identifying safety information these symbols are being used to identify potential risks. When seen a safety symbol in the manual, it must be understood that there is an injury risk and following instructions must be read carefully to avoid potential risks. While welding, keep th...
Page 4
3 monostick 200i pfc safety rules breathing welding fumes can be hazardous to your health inhaling fumes and gases over a long period of time, generated during welding is dangerous and forbidden . Irritation of the eyes, nose and throat are symptoms of inadequate ventilation. Take immediate steps to...
Page 5
4 monostick 200i pfc safety rules noise can damage hearing noise from certain industrial processes or equipments can damage hearing. Wear approved ear protection if noise level is high. Working in small and confined places can be dangerous while welding and cutting in small, confined places, always ...
Page 6
5 monostick 200i pfc safety rules falling unit can cause injury wrong positioned power source or other equipment may cause serious injury to persons or damage to objects. While repositioning the power source always carry by using the lifting eye. Never pull cable, hose or torch. Always carry the gas...
Page 7
6 monostick 200i pfc 2 3 4 5 6 8 1 7 9 power switch power led thermic / error led current adjustment knob earth cable and welding cable socket (-) 1 2 3 4 5 earth cable and welding cable socket (+) line cable inlet handle fan 6 7 8 9 monostick i is an inverter type portable, mono-phase dc mma weldin...
Page 8
Manual metal arc welding direct current descending characteristics line input-1 phase alternating current appropriate to operate in dangerous work area x :duty cycle* u :open circuit voltage u :line voltage and frequency u :rated welding voltage i :input current i :rated welding current ip23s :prote...
Page 9
8 monostick 200i pfc 2.1 upon receipt and claims be sure that you have received all the items that you have ordered. In case of any item is missing or damaged, contact your supplier immediately. In the event of damaged or missing delivery, it to the shipping agency and magma mekatronik with the phot...
Page 10
Figure 2: tig welding connections ar 1.0 1.6 6.3 9.5 15 - 70 30 - 150 6 - 8 6 - 8 install the argon gas regulator onto the argon gas cylinder. C gas hose of the torch the regulator onnect the to gas . Adjust the desired current and the machine is ready to weld. Tig torch with a valve should be used....
Page 11
Contact tip and nozzle on the torch have to be cleaned regularly and changed if required. Contact tips must be in good condition, longer tips generally give better results. Note: the above recommended maintenence periods are indicative, these may vary according to the work shop conditions. If the th...
Page 12
11 monostick 200i pfc 2 3 4 1 8 5 6 9 7 1 2 3 4 5 6 7 8 9 electronic card - control - filter pfc power knob fan electronic card electronic card - electronic card - current adjustment potentiometer thermic / error led - red power led - green power switch no k405000146 7 k4050001 k405000143 k40500014 ...
Page 13
12 monostick 200i pfc electrical diagram appendix 2 earth earth earth current front panel w elding 5mm green 5mm red thermic relay thermic thermic.
Page 14
Made in tÜrkİye owm 06.24.2013 +90 236 226 27 00 +90 236 226 27 28 organize sanayi bölgesi 5.Kısım yalçın Özaras caddesi no:1 45030 manİsa www.Magmaweld.Com factory.