Magnavox 26MF321B Owner's Manual - page 11
These operations are accessible by remote control.
Some may also be accessible by controls on the main unit.
Initial Setup
Thissectionwillguideyouthroughtheunit’sinitialsetting
whichincludesselectingalanguageforyouron-screenmenu
andautoprogram,whichautomaticallyscansandmemorizes
viewablechannels.
Before you begin:
Makesuretheunitisconnectedtoantennaorcable.
1
Aftermakingallthenecessaryconnections,
press toturnontheunit.
• Itmaytakeafewmomentstoturnontheunitforthe
firsttime.
•
[Initial Setup]
menuappearsautomaticallyafterthe
unitisturnedon.
2
Use
▲/▼
toselecttheon-screenlanguagefromthe
choices(English/Español/Français)ontherightsideofthe
TVscreen,thenpress
OK
.
3
Use
▲/▼
toselect
[Antenna]
forTVchannelsor
[Cable]
forCATVchannels,thenpress
OK
.
Initial Setup
Make sure the antenna is connected to ''ANT. IN'' jack.
Select your signal source.
Antenna
Cable
Skip
Antenna
Cable
Or
ANT.IN
Select
OK
OK
BACK
Back
MENU
Skip
•
[Autoprogram]
willbegin.
Initial Setup
Please wait while the system is scanning for channels.
Auto programming may take more than 20 minutes to
complete.
0%
MENU
Skip
4
Use
◄/►
toselectthedesiredlocationsetting,thenpress
OK
.
Initial Setup
Select “Retail” or “Home” for your location.
Retail
Home
Select
OK
OK
• Select
[Retail]
store,theunitwillbesetupwith
predefinedsettingforretaildisplays.
• Select
[Home]
,theunitissettomaximizetheenergy
efficiencyforhomesettinganditcanbeadjusted
throughachoiceofpictureandsoundqualityaccording
toyourpreference.Usethissettingtoremovethe
E-Stickerifvisiblefromthedisplay.
➠
p. 23
• Whentheinitialsetupiscompleted,thelowest
memorizedchannelwiththeconfirmationmessageof
thelocationsettingwillbedisplayedontheTVscreen.
• Youmustset
[Home]
instep
4
.Otherwise,
[Picture]
and
[Sound]
settingsyouadjustedwillnotbe
memorizedaftertheunitgoesintostandbymode.
Note
• Ifyouarenotreceivingasignalfromyourcableservice,contact
theCableprovider.
• Ifyoupress
or
MENU
duringautoprogram,thissetupofTV
channelswillbecanceled.
• Theinitialautoprogramfunctioncanbeexecutedforeither
[Antenna]
or
[Cable]
onlyonce.Whenyouchangethe
connection(Antenna/Cable),set
[Autoprogram]
again.
➠
p. 17
• Ifthereisnosignalinputfromtheantennaterminalandno
operationforseveralsecondsafteryouturnontheunit,helpful
hintsappears.FollowtheinstructionslistedontheTVscreen.
Initial Setup
No channel is registered.
Try Autoprogram again?
Verify that you have a cable connected to the “ANT. IN” jack
on the back of the TV, the channel installation process
searches this connection. If you are using a cable or satellite
box, please confirm the input which you have connected to the
box and press “SOURCE” key on the remote control to select
the appropriate source input.
Retry
Later
Select
OK
OK
MENU
Skip
After an initial setup is completed...
• Ifyouwanttoscanthechannelsautomaticallyagain.
[Autoprogram]
➠
p. 17
• Youcanaddthedesiredcableandanalogchannels
unmemorizedbyautoprogram.
[Add Channels]
➠
p. 18
• Ifyouwanttochangetoanotherlanguage.
[Language]
➠
p. 23
• Ifyouwanttochangethelocationsetting.
[Location]
➠
p. 23
11
IN
TR
O
D
U
C
TIO
N
PR
EPA
RA
TIO
N
W
AT
C
H
IN
G
TV
US
IN
G
FU
N
CT
IO
N
S
U
SE
FU
L T
IPS
CO
NN
EC
TIN
G D
EV
ICE
S
IN
FO
RM
AT
IO
N
English