1. DL manuals
  2. Magner
  3. Cash Counter
  4. 35-2003 Series
  5. Operator's Manual

Magner 35-2003 Series Operator's Manual

Manual is about: MAGNER 35-2003; 35-3 Series Currency Counter

Summary of 35-2003 Series

  • Page 1

    Magner 35-2003/35-3 series currency counter operator's manual.

  • Page 3

    1 magner 35-2003 / 35-3 series introduction. The magner 35-2003 / 35-3 is the most advanced currency counter available today. Magner's design engineer's have gathered input from experienced currency counter experts to develop a machine that is as compact as possible yet fast and extremely accurate. ...

  • Page 4

    2 i. Safety instructions. Warning the currency counter automatically starts operating in certain circumstances. Consequently, it is important to always follow these precautions: 1. Do not wear loose clothing or jewelry while operating the currency counter. 2. Make sure that your hair does not touch ...

  • Page 5

    3 magner 35-2003 / 35-3 series ii. Installation. Unpacking after unpacking the currency counter, store the box and packing materials for future shipping. Failure to ship the currency counter in the original box and packing will void the warranty. Installation 1. Select an appropriate workspace. Make...

  • Page 6

    Iii. Parts description. Sp man. Auto 1 2 3 4 5 6 7 8 9 0 start stop + accm 0 clr d figure 1 : sheet key d size detection key (35-2003 only) sp speed selection key man. Auto manual/auto start key numeric keys start stop start/stop key 0 clr clear key + accm accumulation key density key lcd display (4...

  • Page 7

    Figure 3 : count sensor figure 4 : note jam release lever thickness adjustment dial interface connector (rs-232c / option) or external display connector (option) power switch fuse ac input receptacle voltage selection switch figure 5 : rear view 5 magner 35-2003 / 35-3 series.

  • Page 8

    Iv. Function of parts. 1. Sheet key and function of each key d size detection key (35-2003 only) this function is available with the mode 35-2003. - press d key. "d" appearing on the display indicates that this function is on. - the counting speed is automatically set at speed - 2 when this function...

  • Page 9

    Sp speed selection key - three counting speeds are available on this machine: sp 1: counts approximately 600 notes per minute. Sp 2: counts approximately 1,200 notes per minute. Sp 3: counts approximately 1,500 notes per minute. - to display the counting speed, press sp key. - to change the counting...

  • Page 10

    To set a batch: - touch the desired number using the numeric key. - a 3-digit display indicates the preset batch number. - the machine is now ready to count in the preset batch mode. To clear the current preset batch number and batch setting: - press 0 key until the 3-digit display indicates "0". - ...

  • Page 11

    Level 2: more sensitive than level 3 level 3: more sensitive than level 4 level 4: default level from the factory level 5: the machine accepts any density of notes. When level 5 is in use, in the display will flash. The factory default setting is set at level 4. - to display the density level, press...

  • Page 12

    - two stacker wheels ensure neat stacking of notes at all times. 5. Note jam release lever this lever is used to release the note(s) jammed inside the currency counter. 6. Thickness adjustment dial - this dial is used for adjusting the gap between the feeding and separating rollers so that only one ...

  • Page 13

    11 magner 35-2003 / 35-3 series v. Operating procedure for trouble-free operation, perform the following steps in the order given. 1. Prepare the currency a. Remove and discard clips, rubber bands and tags from the notes to be counted. B. Fan each group of notes before counting as shown in figure6, ...

  • Page 14

    To-count mode. - if a “sensor error code” (see page 10) appears on the display instead of “0”, take corrective actions in accordance with the instructions on page 12. 3. Adjust the thickness adjustment dial the thickness adjustment dial is set at 5 as the standard setting. - for new(thinner) notes, ...

  • Page 15

    Vii. Error codes when an error occurs, the machine immediately stops and produces an electric “beep” while the display alternately flashes the error code and count figure. The note count for the batch in which the error occurred may be inaccurate. Note to ensure an accurate count, recount the last b...

  • Page 16

    3. Operation fault corrective actions: 1. Make sure that the currency counter is plugged into a wall outlet and that the power cord is plugged into the back of the machine. 2. Check that the voltage selection switch matches power input. Call for service. Turn off and unplug the currency counter. Cal...

  • Page 17

    Ix. Preventive maintenance preventive maintenance, requiring partial disassembly by service technicians, is recommended every 180 days. With heavy usage(more than one shift per day, continuous service, etc.), this service will be needed more often. To make sure the operation is as trouble-free as po...

  • Page 18

    X. Specifications counting speed: approximately 600 / 1200 / 1500 notes per minute display type: lcd: 4-digit total display / 3-digit batch display document size limits: 110x185 ~ 50x85 (mm) 4.33x7.28 ~ 1.97x3.35(inches) input hopper capacity: approximately 300 circulated notes output stacker capaci...

  • Page 19

    17 magner 35-2003 / 35-3 series.

  • Page 20

    Ehf-00069 012706.