I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. W w w . M a k i t a t o o l s . C o m angle drill 13 mm (1/2”) model da4000lr 003009 double insulation.
2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa002-2 (for all tools) warning: read and understand all instructions. Failure to follow all instructions listed below, may result in...
3 change the plug in any way. Double insula- tion eliminates the need for the three wire grounded power cord and grounded power supply system. 5. Avoid body contact with grounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body ...
4 model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. Service 23. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injury. 24. When servicing a to...
5 specific safety rules usb001-2 do not let comfort or familiarity with product (gained from repeated use) replace strict adherence to drill safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces when performing...
6 symbols usd201-2 the followings show the symbols used for tool. V ....................... Volts a ....................... Amperes hz ..................... Hertz ................ Alternating current .................... No load speed .................... Class ii construction .../min..................
7 functional description caution: • always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action caution: • before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “off” position when...
8 use of it with angle attachment screw the side grip for the angle attachment on the angle housing. Then tighten the side grip by turning clockwise at the desired position. Use of it without angle attachment screw the side grip on the tool barrel securely. The side grip can be installed on either s...
9 remove the chuck remaining bolt through the chuck opening by turning it counterclockwise with the hex wrench. Caution: • the drill chuck and the bolt are assembled each other. Turn the bolt counterclockwise about 10 times so that they can be removed together. Loosen the bolts of the joint by the h...
10 slide the drill chuck to the spindle so that the two faces are fitted perfectly. Holding the drill chuck with the chuck key, tighten the bolt (for installing the drill chuck) clockwise with the hex wrench firmly. The tool may be converted to a conventional straight drive drill by installing the d...
11 operation holding tool when drilling a large hole with a hole saw, etc., the side grip (auxiliary handle) should be used as a brace to maintain safe control of the tool. Drilling operation drilling in wood when drilling in wood, the best results are obtained with wood drills equipped with a guide...
12 maintenance caution: • always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free t...
13 first-class postage required post office will not deliver without proper postage. Makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 fold cut.
14 1. This product was purchased from: home center hardware/lumber store tool distributor industrial supply construction supply other ( ) 3. How did you learn about this product: magazine from dealer newspaper store display catalog radio exhibition from friend previous usage other ( ) 2. Use of the ...
15 factory service centers 1-800-4-makita retain this portion for your records arizona 3707 e. Broadway rd., ste. 6 phoenix, az 85040 (602) 437-2850 california 41850 christy st. Fremont, ca 94538-5107 (510) 657-9881 14930 northam st. La mirada, ca 90638-5753 (714) 522-8088 1970 fulton avenue sacrame...
Warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline ...
