I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. W w w . M a k i t a t o o l s . C o m angle drill 13 mm (1/2”) model da4030 13 mm (1/2”) model da4031 003008 double insulation.
2 specifications * extended spade grip • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa002-2 (for all tools) warning: read and understand all instructions. Failure to follow all instructions liste...
3 electrical safety 4. Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec- trician to ...
4 21. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool ser- viced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recom- mended by the man...
5 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 7. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation an...
6 symbols usd201-2 the followings show the symbols used for tool. V ....................... Volts a ....................... Amperes hz ..................... Hertz ................ Alternating current .................... No load speed .................... Class ii construction .../min..................
7 functional description caution: • always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action caution: • before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “off” position when...
8 change knob positioned halfway between the position 1 and the position 2, the tool may be damaged. Torque limiter for model da4031 only the torque limiter will actuate when a certain torque level is reached (for lower speed setting: position 1). The motor will disengage from the output shaft. When...
9 spade grip the spade grip can be installed in any position as shown in the figure. To change the position, loosen the hex bolts (both sides) with a hex wrench and turn the spade grip to the desired position. Then tighten the hex bolts securely. After reposition the grip, return the hex wrench to t...
10 operation holding tool caution: • this is a powerful tool. High torque is developed and it is important that the tool should be securely held and properly braced. Grasp the switch handle with one hand and the spade grip with the other hand. When drilling a large hole with a self- feed bit, etc., ...
11 • there is a tremendous twisting force exerted on the tool/ bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece. • a stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. H...
12 accessories caution: • these accessories or attachments are recommended for use with your makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assis...
13 first-class postage required post office will not deliver without proper postage. Makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 fold cut.
14 1. This product was purchased from: home center hardware/lumber store tool distributor industrial supply construction supply other ( ) 3. How did you learn about this product: magazine from dealer newspaper store display catalog radio exhibition from friend previous usage other ( ) 2. Use of the ...
15 factory service centers 1-800-4-makita retain this portion for your records alabama 2365 pelham parkway pelham, al 35124 (205) 620-1791 arizona 3707 e. Broadway rd., ste. 6 phoenix, az 85040 (602) 437-2850 arkansas shackleford shopping center 240 south shackleford rd., ste. C little rock, ar 7221...
Warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline ...
