1. DL manuals
  2. Makita
  3. Brush Cutter
  4. EBH252L
  5. Original Instruction Manual

Makita EBH252L Original Instruction Manual

Summary of EBH252L

  • Page 1

    Ebh252u ebh253u ebh252l ebh253l important: read this instruction manual carefully before putting the petrol brushcutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully! Petrol brushcutter ebh252u ebh253u ebh252l ebh253l original instruction manual.

  • Page 2

    2 thank you very much for purchasing the makita petrol brushcutter. We are pleased to recommend to you the makita petrol brushcutter which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points t...

  • Page 3

    3 15 meters diagrammatic figure safety instructions general instructions read this instruction manual to become familiar with handling of the – equipment. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. It is recommended only to lend the equip...

  • Page 4

    4 • resting • transport • refuelling • maintenance • tool replacement 3 meter s start the brushcutter only in accordance with the instructions. Do not use any other methods for starting the engine! – use the brushcutter and the tools only for such applications as specified. – only start the engine, ...

  • Page 5

    5 caution: kickback diagrammatic figure diagrammatic figure method of operation only use in good light and visibility. During the winter season beware of – slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. Never cut above waist height. – never stand on a ladder. –...

  • Page 6

    6 never straighten or weld damaged cutting tools. Pay attention to the environment. Avoid unnecessary throttle operation for – less pollution and noise emissions. Adjust the carburetor correctly. Clean the equipment at regular intervals and check that all screws and nuts – are well tightened. Never ...

  • Page 7

    7 technical data ebh252u, ebh252l model ebh252u ebh252l bike handle loop handle dimensions: length x width x height (without cutting blade) mm 1,770 x 620 x 490 1,770 x 330 x 275 mass (without plastic guard and cutting blade) kg 5.7 5.3 volume (fuel tank) l 0.5 volume (oil tank) l 0.08 engine displa...

  • Page 8

    8 technical data ebh253u, ebh253l model ebh253u ebh253l bike handle loop handle dimensions: length x width x height (without cutting blade) mm 1,770 x 620 x 490 1,770 x 330 x 275 mass (without plastic guard and cutting blade) kg 5.9 5.4 volume (fuel tank) l 0.5 volume (oil tank) l 0.08 engine displa...

  • Page 9

    9 ⑱ ④ ⑤ ⑦ ⑧ ⑨ ⑪ ⑩ ⑫ ⑬ ⑭ ⑮ ④ ⑤ ⑰ ⑦ ⑨ ⑪ ⑩ ⑫ ⑭ ⑯ ebh252l ebh253l ebh252u ebh253u ① ③ ⑥ ⑲ ② 22 21 designation of parts gb designation of parts 1 fuel tank 2 rewind starter 3 air cleaner 4 i-o switch (on/off) 5 spark plug 6 exhaust muffler 7 clutch case 8 rear grip 9 hanger 10 handle 11 control lever 12 ...

  • Page 10

    10 caution: before doing any work on the petrol brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! Caution: start the petrol brushcutter only after having assembled it completely. For machines with bike handle models – loosen knob...

  • Page 11

    11 to meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine makita cutter blades or nylon cutting head. – the cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone...

  • Page 12

    12 turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily. – insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench. – loosen the nut (1) (left-hand thread) with the socket wrench and ...

  • Page 13

    13 inspection and refill of engine oil – perform the following procedure, with the engine cooled down. – while keeping the engine level, remove the oil gauge, and confirm that the oil is filled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches ...

  • Page 14

    14 refueling handling of fuel it is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for ...

  • Page 15

    15 attachment of shoulder strap – adjust the strap length so that the cutter blade will be kept parallel with the ground. For ebh252u, ebh253u note: be careful not to trap clothing, etc., in the buckle. Observe the applicable accident prevention regulations! Starting move at least 3 m away from the ...

  • Page 16

    16 2) set the i-o switch (1) to operation. 3) choke lever close the choke lever. Choke opening: – full closing in cold or when the engine is cold. – full or half opening in restart just after stop of operation. Note: – if the starter handle is pulled repeatedly when the choke lever remains at “close...

  • Page 17

    17 b: startup after warm-up operation 1) push the primer pump repeatedly. 2) keep the throttle lever at the idling position. 3) pull the recoil starter strongly. 4) if it is difficult to start the engine, open the throttle by about 1/3. Pay attention to the cutter blade which may rotate. Stopping 1)...

  • Page 18

    18 nylon cutting head the nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms. The nylon cutting head will automatically feed out the proper length of nylon cord by the changes in centrifugal force caused by increasing or decreasing rpms. However, to...

  • Page 19

    19 replacement of engine oil deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of replacement. Attention: in general, the engine main unit and engine oil still remain hot just after the engine is stopped. In re...

  • Page 20

    20 cleaning of air cleaner danger: inflammables strictly prohibited interval of cleaning and inspection: daily (every 10 operating hours) – turn the choke lever to the full close side, and keep the carburetor off from dust or dirt. – remove the air cleaner cover-­fixing bolts. – pull the cover lower...

  • Page 21

    21 cleaning of fuel filter warning: inflammables strictly prohibited interval of cleaning and inspection: monthly (every 50 operating hours) suction head in the fuel tank – the fuel filter (1) of the suction head is used to filter the fuel required by the carburetor. – a periodical visual inspection...

  • Page 22

    22 warning: when draining the fuel, be sure to stop the engine and confirm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire. Attention: when the machine is kept out of operation for a long time, drain up all fuel from the...

  • Page 23

    23 *1 perform initial replacement after 20h operation. *2 for the 200 operating hour inspection, request authorized service agent or a machine shop. *3 after emptying the fuel tank, continue to run the engine and drain fuel in the carburetor. Operating time item before operation after lubrication da...

  • Page 24

    24 troubleshooting before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact authorized service agent or local d...

  • Page 25

    25.

  • Page 26

    26.

  • Page 27

    27.

  • Page 28

    Makita corporation anjo, aichi, japan 884909f228 www.Makita.Com ala.