MEGATRONIX KE 680 Installation And Operation Manual - page 7
KE680
7
FEATURE “
II
” PRORAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch 4 times and hold it on the 4
th
push until two chirps with a long chirp is heard. Then
release the valet switch. You are now in the Feature
‘II’ programming mode.
3. Press and release the trans
mitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
One LED Pulse
Factory Default
Setting
Two Chirps /
Two LED Pulses
Three Chirps /
Three LED Pulses
Four Chirps /
Four LED Pulses
1
0.9-second door
lock pulses.
3.5-second door lock
pulse.
Double pulse unlock
Door lock with
“Comfort Feature”
2
or F
Ignition controlled
door lock &
unlock
Ignition controlled
door lock only
Ignition controlled
door unlock only
Without ignition
controlled door lock
& unlock
3
or
Pathway
illumination
feature “off”
Parking light “on” for
30 seconds upon an
unlock signal
Parking light “on” for
30 seconds upon an
unlock signal & 10
seconds upon a lock
signal.
Exit: Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Comfort Feature:
Some Vehicles have a special “COMFORT feature”. When you lock the door with the key, you just have to
keep on turning the key on the door about 5 or 7 seconds and the window will close directly.
If your vehicle with “COMFORT feature” and you wish the door being locked and the window being closed
automatically at the same time by remote control, you can set the alarm feature
II-1
“with comfort feature”.
FEATURE “
III
” PRORAMMING:
1.
Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch 6 times and hold it on the 6
th
push until three chirps with a long chirp is heard.
Then release the valet switch. You are now in the Feature
‘III’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
1
H1/4 Brown Wire =
Constant siren
output for six-tone
siren
H1/4 Brown Wire =
5-second pulse siren
output for single-tone
siren
H1/4 Brown Wire =
Random pulse siren
output
H1/4 Brown Wire =
Pulse output
2
or F
H7/7 Red / White
Wire Channel 3 =
1 second pulse
output for trunk
release.
H7/7 Red / White
Wire Channel 3 =
Latch output
H7/7 Red / White
Wire Channel 3 =
Timer controlled
output
3
or
H7/10 Purple /
Black Wire Channel
4 =
Momentary output
H7/10 Purple / Black
Wire Channel 4 =
Latched output
H7/10 Purple / Black
Wire Channel 4 =
Latched output and
reset with ignition
“ON”
H7/10 Purple / Black
Wire Channel 4 =
Timer programming
(set to any interval
between 1 second
and 2 minutes.)
Exit: Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Channel 3 (4) Timer Control Output Programming
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch 6 times and hold it on the 6
th
push until three chirps with a long chirp is heard.
Then release the valet switch. You are now in the Feature
‘III” programming mode.