1. DL manuals
  2. N-Tron
  3. Switch
  4. 608MFX-ST
  5. Network Configuration Manual

N-Tron 608MFX-ST Network Configuration Manual

Summary of 608MFX-ST

  • Page 1

    1 600 series industrial ethernet switches network configuration guide.

  • Page 2: Industrial Ethernet Switch

    2 industrial ethernet switch network management guide 608mfx-st 608mfxe-st-15 608mfxe-st-40 608mfxe-st-80

  • Page 3

    3 copyright, © n-tron corp., 2002 578 azalea rd. Suite 105 mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a registered trademark of xerox corporat...

  • Page 4: Safety Warnings

    4 safety warnings electrical safety warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: do not work on equipment or cables during periods of lightning activity. Warning: do not perform any services on the unit u...

  • Page 5: 608Mfx Network Configuration

    5 608mfx network configuration the n-tron 608mfx is a product derivative of the osm/esm family jointly manufactured by siemens and n-tron. Some of the software menus may refer to the osmtp62 (optical systems module) or esm (electrical systems module) when identifying the n-tron 608mfx. These names a...

  • Page 6

    6 enter your administrator or user password and press [return]. The cli then displays the start menu and the prompt cli> you can now activate the commands of the cli. Reset you can reset the 608mfx by depressing and holding the select/set button. If necessary, depress the select/set button until the...

  • Page 7

    7 cli commands this section explains the commands of the cli, their functions and syntax. The commands that are available depend on the access level; in other words, whether you logged in as user or as administrator. Table 3–2 contains an overview of the commands available for the administrator and ...

  • Page 8

    8 example: the following example illustrates how to use cli commands. The command status [ports] is used to enable or disable 608mfx ports. The user enters the following: status followed by a blank and then the mandatory setting either e (= enable) or d (= disable) and then the optional port numbers...

  • Page 9

    9 table 3–2 start menu commands - continued osm opens the optical systems module menu. You make the 608mfx– specific settings (for example fault mask) in the osm menu. Agent opens the agent menu. You can enter the settings for network management (for example ip address) in the agent menu. Switch ope...

  • Page 10

    10 table 3-3 settings in the system menu – continued memreset restores the defaults of the 608mfx. The device is automatically restarted. Administrator command restores the factory settings of the 608mfx. With the exception of the ”protected settings”, the settings made by the user are reset to the ...

  • Page 11

    11 table 3-3 settings in the system menu – cont. Cfgname enters the name (max. 32 characters) under which the 608mfx configuration is loaded or stored as a file on the tftp server. Depending on the configuration of the tftp server, this may also include further path names. Administrator only cfgsave...

  • Page 13

    13 table 3–4 settings in the osm menu – cont. Resetc resets the 608mfx counters. Administrator only observer enables, disables and restarts the observer. The operating state of the observer can be read out with the info command. Administrator only agent menu the agent menu includes settings required...

  • Page 15

    15 table 3–5 settings in the agent menu – cont. Ping [count] [size] sends a ping to the specified ip address. Example: ping -c 10 -s 128 192.168.1.1 ten (count) pings with a frame length (size) of 128 bytes are sent to ip address 192.168.1.1. Showec shows the current event configuration. Setec d> se...

  • Page 18

    18 table 3–7 settings in the port menu - continued stat [port] shows the counter readings - of the frame length (s) - of the frames (t) - of the errors (e) of the selected port. The counters are reset with clear. Examples: show s 1,3-5 shows the frame length of ports 1 and 3 through 5. Name with thi...

  • Page 20

    20 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller. If a product does no...

  • Page 21

    21 replacement, or refund of the purchase price paid, at n- tron's option. To the full extent allowed by law, the foregoing warranties and remedies are exclusive and are in lieu of all other warranties, terms, or conditions, express or implied, either in fact or by operation of law, statutory or oth...

  • Page 22

    22 allowed to be excluded in their entirety, they will be limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which may vary depending on local law. Governing law: this limited warranty shall be governed by the laws of the state of alabama, u.S.A...