- DL manuals
- NAD
- Amplifier
- C356BEE
- Owner's Manual
NAD C356BEE Owner's Manual
Summary of C356BEE
Page 1
English por tuguÊs fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ owner’s manual ® c 356bee stereo integrated amplifier.
Page 2
Save these instructions for later use. Follow all warnings and instructions marked on the audio equipment. 1 read instructions - all the safety and operating instructions should be read before the product is operated. 2 retain instructions - the safety and operating instructions should be retained f...
Page 3
19 damage requiring service - unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power supply cord or plug is damaged. B) if liquid has been spilled, or objects have fallen into the product. C) if the product has be...
Page 4
Notes on environmental protection at the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this o...
Page 5
Introduction getting started unpacking and setup what’s in the box packed with your c 356bee you will find: • the sr 8 remote control with 2 (two) aa batteries • this owner’s manual • a detachable mains power cord save the packaging please save the box and all of the packaging in which your c 356bee...
Page 6
Identification of controls front panel 1 standby button: with the rear panel power switch set to on position, press this button to switch on the c 356bee from standby mode. The standby led indicator will turn from amber to blue. Pressing the standby button again turns the unit back to standby mode. ...
Page 7
8 input selectors: these buttons select the active input to the c 356bee and the signal sent to the loudspeakers, headphones and the pre out sockets. The corresponding buttons on the remote control handset duplicate these buttons. When selected, the corresponding input led indicator embedded around ...
Page 8
1 rs-232: connect this interface using rs-232 serial cable (not supplied) to any windows® compatible pc to allow remote control of the c 356bee via compatible external controllers. Nad is a certified partner of amx and crestron and fully supports these external devices. Check out the nad website for...
Page 9
9 tape 2 in/out: connections for analog recording and playback to a tape recorder of any type. Using twin rca-to-rca leads, connect the left and right “audio output” of the tape recorder to the tape 2 in sockets for playback. Connect the left and right “audio input” of the tape recorder to the tape ...
Page 10
A mc input: input for a moving coil phono cartridge. Connect the twin rca lead from your turntable to this input if you are using a moving coil cartridge. B mc-mm switch: slide this switch to either mm (moving magnet) or mc (moving coil) depending upon the phono cartridge being used. C phono ground ...
Page 11
Using the sr 8 remote control the sr 8 remote control handset handles the key functions of the c 356bee as well as other nad stereo receivers, integrated amplifiers and preamplifiers. It has additional controls to remotely operate nad cd players, am/fm tuners and dedicated am/fm/db tuners. It will o...
Page 12
Cd player control (for use with compatible nad cd player): set the device selector to “cd” in order to gain access to these buttons. Some of the control buttons below are applicable only to specific nad cd player models; check the owner’s manual of your nad cd player for control button compatibility...
Page 13
Using the sr 8 remote control library the sr 8 can store a different library of default nad codes for each of its device selector “pages.” if the original default library does not control your nad cd player, dvd player, or other component, follow the procedure below to change the library code. Refer...
Page 14
Condition possible causes possible solutions no sound. • mains power cord unplugged or power not switched on. • check if mains power cord is plugged in and power switched on. • tape monitor selected. • de-select tape monitor mode. • mute on. • switch off mute. • rear pre out/main in amp links not fi...
Page 15
Preamplifier section line level input, pre out thd 1 20 hz – 20 khz, ccif imd, smpte imd, dim 100 signal-to-noise ratio >106 db (ihf; a-weighted, ref. 500 mv out, unity gain) >114 db (a-weighted, ref. 2 v out, volume maximum) >92 db (ref. 100 mv out, unity gain) channel separation -1 khz >80 db 10 k...
Page 16
Phono section (with optional pp 375 installed) mm/mc in, pre out input impedance - mc 100 ohms (r) 180 pf (c) mm 47 kohms (r) 180 pf (c) input sensitivity 2 for 80 w in 8 ohms - mc 0.38 mv 1 khz mm 5.0 mv 1 khz input sensitivity 2 for 1 w in 8 ohms - mc 39 uv 1 khz mm 0.56 mv 1 khz input overload - ...
Page 17
17 english por tuguÊs fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ.
Page 18
Www.Nadelectronics.Com ©2013 nad electronics international a division of lenbrook industries limited all rights reserved. Nad and the nad logo are trademarks of nad electronics international, a division of lenbrook industries limited. No part of this publication may be reproduced, stored or transmit...