NAD C356BEE Owner's Manual - page 7
8 INPUT
SELECTORS: These buttons select the active input to the
C 356BEE and the signal sent to the loudspeakers, headphones and the
PRE OUT sockets. The corresponding buttons on the remote control
handset duplicate these buttons. When selected, the corresponding
input LED indicator embedded around the bezel of the particular input
button will illuminate blue.
MP (MEDIA PLAYER): Selects a line-level source connected to the MP
sockets as the active input.
If an external Media Player is connected to the front MP socket (using
a 3.5mm stereo plug) while listening to a MP line-level source, the
external Media Player will be directly selected with the MP line-level
source immediately disconnected. It is recommended to mute the
volume or switch to a different input before plugging/unplugging the
external Media Player cable.
CD: Selects the CD player (or other line-level source) connected to the
CD sockets as the active input.
TUNER: Selects the tuner (or other line-level source) connected to the
tuner sockets as the active input.
DISC/MDC: Selects a line-level source connected to the DISC sockets.
If an optional Modular Design Construction (MDC) module is installed,
the DISC input socket is disabled and the MDC source is selected as the
active input.
AUX: Selects a line-level source connected to the AUX sockets as the
active input.
TAPE 2: Selects TAPE 2 as the active input.
TAPE MONITOR: Selects the output from a tape recorder when playing
back tapes or monitor recordings that are being made through the
TAPE MONITOR sockets.
TAPE MONITOR does not override the current input selection. For
example, if CD is the active input when TAPE MONITOR is selected, then
the CD signal will continue to be selected and sent to both the TAPE 2
and TAPE MONITOR output sockets, but it is the sound from recorder
connected to TAPE MONITOR that will be heard in the loudspeakers.
Apart from the TAPE MONITOR LED illuminated to indicate it is engaged,
the corresponding LED indicator for the active input will also stay
illuminated.
9 TONE
DEFEAT: Tone Controls are enabled or disabled by pressing this
button. When enabled (TONE DEFEAT LED indicator is illuminated), the
Tone Control circuits are bypassed. The Tone Control circuits are active
when the TONE DEFEAT LED indicator stays extinguished.
10 TONE CONTROLS: The C 356BEE is fitted with BASS and TREBLE tone
controls to adjust the tonal balance of your system. The 12 o’clock
position is “flat” with no boost or cut, and an indent indicates this
position. Rotate the control clockwise to increase the amount of Bass or
Treble. Rotate the control counterclockwise to decrease the amount of
Bass or Treble. The Tone controls do not affect recordings made using
the TAPE output terminals but will affect the signal going to the Pre-
amp output terminals (PRE OUT 1 and PRE OUT 2).
11 BALANCE: The BALANCE control adjusts the relative levels of the
left and right speakers. The 12 o’clock position provides equal level to
the left and right channels. A detent indicates this position. Rotating
the control clockwise moves the balance towards the right. Rotating
the control counterclockwise moves the balance to the left. The
BALANCE control does not affect recordings made using the TAPE
output terminals but will affect the signal going to the Pre-amp output
terminals (PRE OUT 1 and PRE OUT 2).
12 VOLUME: The VOLUME control adjusts the overall loudness of the
signals being fed to the loudspeakers or headphones. Turn clockwise
to increase the volume level; counter clockwise to lower it. The
VOLUME control does not affect recordings made using the TAPE
output terminals but will affect the signal going to the Pre-amp output
terminals (PRE OUT 1 and PRE OUT 2).
IDENTIFICATION OF CONTROLS
FRONT PANEL
7
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ