NAD C717 Owner's Manual - page 9
1 ac power cord: Plug the AC power cord into a live AC wall socket.
Make sure all connections have been made before connecting to mains.
Connect only to the prescribed AC Outlet, i.e., 120V 60 Hz or 230V 50 Hz.
2 Subw (Subwoofer) out: Connect this output to a powered
(“active”) subwoofer or to a power amplifier channel driving a passive
system).
3 SpeakerS: Connect the left and right terminals to the corresponding
loudspeakers. Each output’s “+” (red) terminal and “-” (black) terminal
must be connected to the corresponding “+” and “-” terminals of the
loudspeaker. Use extra care to ensure that no stray wires or strands cross
between posts or terminals at either end.
NOTES
• Usestrandedwireofatleast16-gauge(AWG);specializedspeakercable
maybevaluable(consultyourNADaudiospecialist).Connectionstothe
C717canbemadewithbanana-typeplugs,orusingbarewire,orpins,
bylooseningtheterminal’splasticnut,makingaclean,neatconnection,
andre-tighteningcarefully.Tominimizethedangerofshort-circuits,
ensurethatonly1/2-inchofexposedwireorpinisemployedin
connecting.
• Thisunitisdesignedtoproduceoptimumsoundqualitywhenconnectedto
speakerswithimpedanceswithintheC717’soperatingrange.Pleasecheck
thatspeakersareratedtobe6ohmsminimumperspeaker.
4 Scart/rgb out: Connect the C 717’s “SCART/RGB OUT” to the SCART/
RGB video input of a compatible video monitor/TV. Be sure to observe
the correct orientation of the SCART/RGB plug. Make sure also to set
“VIDEO OUT” to “RGB” at the SETUP menu for stable video availability at
SCART/RGB OUT.
5 optical digital out: Connect the OPTICAL DIGITAL OUT port
to the corresponding S/PDIF digital input of a receiver, computer
soundcard or other digital processors.
6 video out: Connect to the corresponding composite video input of
a compatible monitor/television, projector, A/V receiver or processor
using quality dual-RCA cable designed for video signals.
7 component video out: Connect the C 717’s “COMPONENT VIDEO
OUT” to the component video input of a compatible video monitor/TV.
Be sure to observe consistency in connecting the appropriate Y, Cb/Pb,
Cr/Pr jacks to the corresponding sources/inputs. Do not rely purely
on the color coding of the jacks, which may not always be consistent
among brands. The routing of the component video output is fixed.
NOTES
• Makesuretoset“VIDEOOUT”to“COMPONENT”attheSETUPmenufor
videotobeavailableatComponentVideoOUT.Referalsototheitem
aboutVIDEOOUTundertheUSINGTHEC717’sINTERNALDVDPLAYER
-SETUPMENUsectionoftheOPERATIONpage.
• “COMPONENTVIDEOOUT”willonlydisplaytheinternalDVDvideo
signals.
8 vcr in/out: VCR may be used with recording components such as a
cassette deck. Connect analog stereo audio from such source components
into the C715’s VCR IN. Connect the C 717’s VCR OUT to the source
components’ record-input. Note that VCR may freely be used for play-only
components, in which case the OUT jacks would remain unconnected.
NOTES
• TherewillbenooutputatVCROUTwhenVCRisactivesourceinput.
Thispreventsfeedbackthroughtherecordingcomponentthereby
preventingpossibledamagetoyourspeakers.
• VCRIN/OUTisforaudiosignalonly.
IDENTIFICATION OF CONTROLS
rear panel
ATTENTION!
PleasemakealltheconnectionstoyourC717withtheunitunplugged.Itisalsoadvisabletopowerdownorunplugallassociatedcomponentswhile
makingorbreakinganysignalorACpowerconnections.
1
2
5
4
3
6
7
8
9 10
9
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ