NAD M15 HD Owner's Manual - page 7
1 STANDBY LED
• This indicator will light up amber when the M15 HD is at standby
mode.
• When the M15 HD is powered up from standby mode, this indicator
will illuminate blue.
• If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY button
is pressed to switch the M15 HD to standby mode, the VFD will
be extinguished but the STANDBY LED remains illuminated blue.
This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. The
corresponding active Zone icon(s) will also remain displayed in the
VFD.
• In order to completely shut down the M15 HD with Zone 2, Zone
3 and/or Zone 4 still ON, press and hold STANDBY button until the
STANDBY LED turns amber.
• In the unlikely event that the M15 HD switches to protection state,
this indicator will illuminate red.
• When infrared command from the HTRM is received, this indicator
will also flash momentarily.
2 STANDBY BUTTON
• Press this button to switch ON the M15 HD from standby mode. The
Standby LED indicator will turn from amber to blue and illuminate
the VFD. Pressing the STANDBY button again turns the unit back to
standby mode.
• The M15 HD can also be switched ON from standby mode by
pressing any of the front panel buttons.
NOTES
• TherearpanelPOWERswitchmustbeintheONpositionfortheStandby
buttontoactivate.
• If“AutoTriggerIn”atTriggerSetupmenuisassignedto“Main”or“All”
andthe+12VTRIGGERINswitchissetto“AUTO”mode,thestandby
buttoninthefrontpanelaswellasthecorrespondingON/OFFfunction
keysintheHTRMremotecontrolwillbedisabledeffectivelyhandling
thisfunctiontoanexternalcontroller.Slideto“OFF”the+12VTRIGGER
INswitchtomaintainnormalpowerON/OFFfunctionprocedures.
3 REMOTE SENSOR
• Point the HTRM remote control at the remote sensor and press the
buttons.
• Do not expose the remote sensor of the M15 HD to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the M15 HD with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30o in each direction of the front of the remote sensor.
4 VACUUM FLUORESCENT DISPLAY (VFD)
• Displays visual information about the current settings like the active
Source, volume level, listening mode, audio format, iPod-related
display information and other related indicators.
• Refer also to the item about DISPLAY SETUP under the USING THE
M15 HD - SETUP MENU segment of the OPERATION section.
5 VOLUME
• Use this control to adjust the overall loudness of the signal output at
AUDIO PRE-OUT.
• The default volume level is -20dB.
• The VOLUME knob is also used to increment/decrement other
adjustable parameters like Tone Controls.
6 3 SOURCE 4
• Toggle through the input selections - Source 1, Source 2, Source 3,
iPod, Source 5, Source 6, Source 7, Source 8 and Source 9.
• Refer also to the item about SOURCE SETUP under the USING THE
M15 HD - SETUP MENU segment of the OPERATION section.
7 INFO
• Show information as supplied by the applicable source.
• Toggle [INFO] button to display supplied information.
IDENTIFICATION OF CONTROLS
FRONT PANEL
4
5
11
1
2
3
10
9
8
7
6
6
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ