NAD M15 HD Owner's Manual - page 27
DISPLAY SETUP
The Vacuum Fluorescent Display (VFD) and On-Screen Display (OSD) can be
shown in various ways by navigating through the parameters at the ‘Display
Setup’ menu. Use a combination of or ENTER and
keys to step
through the ‘Display Setup’ menu items.
NOTE
Theconfigurationssetforthat‘DisplaySetup’arecarriedoverwhenever
itisenabledduringA/VPresetsetting.Pleaseseealsothesectionbelow
about‘AVPresets.’
VACUUMFLUORESCENTDISPLAY(VFD)
Display: Select ‘On’ to display all applicable data or characters at the
VFD. Nothing will be shown at VFD if ‘Temp’ is selected. At ‘Temp’ setting
however, whenever any of the front panel controls or their corresponding
keys in the remote control is activated, the appropriate VFD characters will
be shown temporarily and then fade away. Note that if any of the Zones
are at powered state, they will be continually shown at VFD even at ‘Temp’
setting.
Dimmer: If it is desired to reduce the brightness of the VFD, set Dimmer to
‘Dim’. Otherwise, select ‘Bright’ to return to normal VFD brightness.
Line1,Line2: The VFD shows two main lines of data or characters. Line
2 is the line of data or characters located at the lower bottom of the VFD
while directly above it is Line 1. For both lines, one can select which display
could be shown by choosing through the following
MainSource: Shows the active Source.
Volume: Current Volume level is shown.
ListeningMode: Selected Listening Mode is shown.
AudioSrcFormat: Shows the active Source’s detected audio format.
AudioCodec: Displays the detected audio stream format like Analog,
PCM Surround, Dolby TrueHD, DTS-HD Master Audio and other formats.
VideoMode: Show the video resolution of the active input source.
Details shown include the video resolution with frame rate. For a better
understanding of these video details, consult with your NAD Audio
Specialist or your distributor’s technical department.
Zone2-Zone3-Zone4Source: The assigned Source for the
applicable Zone is shown.
Off: Select ‘Off’ if it is desired not to show any data at the applicable Line.
TempLine: Choose between Line 1 and Line 2 as the desired line where
VFD will be temporarily shown if ‘Temp’ is selected at ‘Display’ option as
described above.
ON-SCREENDISPLAY(OSD)
TempDisp: This applies to the OSD that is temporarily shown at video out
whenever any of the front panel controls or their corresponding keys in the
remote control is activated. Set to ‘On’ if it is desired to show the applicable
OSD at the monitor/TV; otherwise, select ‘Off’.
A/V PRESETS
The M15 HD’s simple but powerfully flexible system of ‘Presets’ allows you
to customize virtually every aspect of your audio-video playback, and recall
them with a single key-press. The parameters ‘Listening Mode’, ‘DSP Options’,
‘Tone Controls’ and ‘Picture Controls’ accessible via the ‘Main Menu’ together
with ‘Speaker Setup and ‘Display Setup’ configurable through ‘Setup Menu’
are stored together as a Single Preset.
You might create one Preset optimized for pop music and another for classical.
One more Preset can be set up to recall each family member’s favorite setting
or one for fully cinematic home-theater playback and yet another one for late-
night movies, with each Preset fine-tuned to a particular scenario or preference.
CREATINGPRESETS
Creating a Preset consists simply of storing a complete set of the
parameters set forth in the ‘Listening Mode,’ ‘DSP Options’, ‘Tone Controls’
and ‘Picture Controls’ accessible via the ‘Main Menu’ together with ‘Speaker
Setup and ‘Display Setup’ configurable through ‘Setup Menu.’
Scroll to ‘A/V Presets’ using the
keys to save a collection of said
parameter settings to a Preset. Select a Preset number and by a
combination of pressing the
keys, you can selectively include in
the particular Preset any of the above-mentioned parameter settings by
choosing ‘Yes’. If you decide not to include in the particular Preset a certain
parameter setting, select ‘No’.
Now in order to save the settings chosen for the particular Preset number,
scroll down to ‘Save Current Setup to Preset’ and press the key. If you
chose to load instead the default settings, scroll down to ‘Load Defaults to
Preset’ and press the key to restore the default settings.
In addition to the parameter settings, the Preset label itself can be assigned a
new name. This new Name will be shown in the VFD as well as on the OSD.
To rename the Preset label, scroll to ‘Name’ and press to go the character.
Then, press
to pick and select through the alphanumeric selections.
Press
to move to the next character or back to the previous character
and at the same time save the changes done on the current character.
NOTE
TheselectedPresetremainsinforceuntilyouselectadifferentPreset.
OPERATION
USINGTHEM15HD–SETUPMENU
7
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ