NAD T 187 Owner's Manual - page 9
4 XM MODULE INPUT (120V version model only)
With XM radio, there are more than 100 channels of music, news, sports,
comedy, talk and entertainment. You will find that the coverage is
continent wide. The music quality is digital with many commercial-free
music channels.
t Connect XM radio cable to this socket. Follow the instructions that
came with your XM radio.
t Refer also to the “LISTENING TO XM RADIO” segment of the
“OPERATION” section.
NOTE
The external XM radio is not supplied with your T 187.
DAB MODULE INPUT (230V version model only)
The T 187 is compatible only with the NAD DAB Adaptor module
models DB 1 or DB 2. With DAB, you can receive CD-like quality
programs without any annoying interference and signal distortion.
t Plug-in the other end of the Mini-Din connector from the NAD DAB
Adaptor module output port into this socket.
t Refer also to the item about “LISTENING TO DAB RADIO” segment of
the “OPERATION” section.
NOTE
The external NAD DAB Adaptor module is not supplied with your T 187.
5 ETHERNET/LOCAL AREA NETWORK (LAN) PORT
LAN connection must be setup for wired connection to be established.
Set up a Wired Ethernet broadband router with broadband internet
connection. Your router or home network should have a built-in DHCP
server to consummate the connection.
t Using a standard straight-through Ethernet cable, connect one
end of the Ethernet cable to the LAN port of your wired Ethernet
broadband router and the other end to T 187’s LAN port.
t This Ethernet connection has similar function as that of the RS232
connection. With your PC and the T 187 on the same network,
it allows remote control of the T 187 via compatible external
controllers.
t Refer to the NAD website for information about RS232 Protocol
documents and PC interface program.
NOTES
t NAD is not responsible for any malfunction of the T 187 and/or the
internet connection due to communication errors or malfunctions
associated with your broadband internet connection or other connected
equipment. Contact your Internet Service Provider (ISP) for assistance or
the service bureau of your other equipment.
t Contact your ISP for policies, charges, content restrictions, service
limitations, bandwidth, repair and other related issues pertinent to
internet connectivity.
6 MP
DOCK
The T 187 is equipped with a data port in the rear panel where an
optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later
variants can be plugged in.
t Connect the “MP DOCK (DATA PORT)” jack of the T 187 to the
corresponding “DATA PORT” socket of the optional NAD IPD model.
t AUDIO 5 and S-VIDEO 3 are the assigned default ports for the audio/
video output of the separately sold NAD IPD (NAD IPD Dock for
iPod) 1, NAD IPD 2 and later variants.
t Refer also to the “LISTENING TO YOUR iPod PLAYER” segment of the
“OPERATION” section.
NOTE
The NAD IPD Dock for iPod is not supplied with your T 187.
7 RS
232
NAD is a certified partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
t Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the T 187
via compatible external controllers.
t Refer to the NAD website for information about RS232 Protocol
documents and PC interface software.
8 +12V
TRIGGER
OUT
The T 187 has three +12V TRIGGER OUT ports (OUT 1, OUT2 and OUT3)
that can be configured to supply +12V DC to a linked component or
system. See discussion on “Trigger Setup” at the “Setup Menu” literature
for guidelines on how to configure +12V TRIGGER IN/OUT.
t Use a 3.5mm mini-jack connector to pass +12 volts at a maximum
current of 50 milliamps to an auxiliary equipment such as a
multichannel amplifier or subwoofer. The center conductor (hot) of
the 3.5mm jack is the control signal. The outside conductor (shield)
is the ground return-path.
t This output will be 12V when the T 187 is ON and 0V when the unit
is either OFF or in standby mode.
+12V TRIGGER IN
With this input triggered by a 12V DC supply, the T 187 can be switched
ON remotely from standby mode by compatible devices such as
amplifiers, preamplifiers, receivers, etc. If the 12V DC supply is cut off,
the T 187 will return to standby mode.
t Connect this +12V Trigger input to the remote device’s
corresponding +12V DC output jack using a mono cable with
3.5mm male plug. The controlling device must be equipped with a
+12V trigger output to use this feature.
9 IR IN/IR OUT 1-3
These mini-jacks accept and output remote-controlled codes in
electrical format, using industry-standard protocols, for use with “IR-
repeater” and multi-room systems and related technologies.
t All NAD products with IR IN/IR OUT features are fully compatible with
the T 187. For non-NAD models, please check with your other product’s
service specialists as to their compatibility to the T 187’s IR features.
IR IN
t This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another compatible device
to allow control of the T 187 from a remote location.
IR OUT 1, IR OUT 2
t Connect T 187’s IR OUT 1 (and/or IR OUT 2) to the IR IN jack of a
compatible device.
t Command and control the linked compatible device by directing its
own remote control to T 187’s infrared receiver.
IR IN and IR OUT 1, IR OUT 2, IR OUT 3
t Connect the T 187’s IR IN to the IR OUT of a compatible device.
Connect also the T 187’s IR OUT 1 (and/or IR OUT 2, IR OUT 3) to the
IR IN of a compatible device.
t With this setup, the T 187 acts as an “IR-repeater” allowing the device
connected to the T 187’ s IR IN control or command of the other
device linked to T 187’s IR OUT 1 (and/or IR OUT 2, IR OUT 3).
IR OUT 3
t IR OUT 3 can only function as an “IR-repeater” as described above.
IDENTIFICATION OF CONTROLS
REAR PANEL
9
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
Р
У
С
СКИЙ