- DL manuals
- NAD
- Receiver
- T 758
- Owner's Manual
NAD T 758 Owner's Manual
Summary of T 758
Page 1
? t 758 av surround sound receiver english por tuguÊs fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ owner’s manual.
Page 2
Save these instructions for later use. Follow all warnings and instructions marked on the audio equipment. 1 read instructions - all the safety and operating instructions should be read before the product is operated. 2 retain instructions - the safety and operating instructions should be retained f...
Page 3
22 wall or ceiling mounting - the product should be mounted to a wall or ceiling only as recommended by the manufacturer. 23 heat - the product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. 24 headphone...
Page 4
Thank you for choosing nad. The t 758 av surround sound receiver is a technologically advanced and highly capable product yet we have invested great effort in making it simple and easy to use. The t 758 delivers a range of genuinely useful options for surround sound and stereo listening alike, using...
Page 5
Introduction getting started what’s in the box packed with your t 758 you will find • quick setup guide • bluos kit containing usb hub, wi-fi dongle, bluetooth usb micro adapter and usb to usb cable extender • avr 4 remote control with 2 aa batteries • bluos-ready flyer/bluesound player • zr 7 zone ...
Page 6
Identification of controls front panel 1 standby button • press this button to switch on the t 758 from standby mode. The standby led indicator will turn from amber to blue and illuminate the vfd. Pressing the standby button again turns the unit back to standby mode. • the t 758 can also be switched...
Page 7
6 vacuum fluorescent display (vfd) • displays visual information about the current settings like the active source, volume level, listening mode, audio format and other related indicators. • refer also to the item about display setup under the using the t 758 - setup menu segment of the operation se...
Page 8
1 ht 2/surr-b ht 1/surr-b • connect ht 2/surr-b and/or ht 1/surr-b to the audio input of an external power amplifier hooked up with up to 4 height speakers. 2 usb • connect the usb connector of the supplied bluos/usb hub to this usb input. Ensure that the wi-fi dongle and bluetooth usb micro adaptor...
Page 9
6 ir in/ir out 1-2 these mini-jacks accept and output remote-controlled codes in electrical format, using industry-standard protocols, for use with “ir repeater” and multi-room systems and related technologies. • all nad products with ir in/ir out features are fully compatible with the t 758. For no...
Page 10
Using the avr 4 remote control the avr 4 remote control handset handles the key functions of the t 758. The avr 4 can also be used to directly command other nad products that respond to applicable common remote control codes. This includes other nad stereo receiver, integrated amplifier and preampli...
Page 11
11 vol 5/6 • increase or decrease loudness level. Release the button when desired level is reached. • the vfd on the front panel will indicate the level set. For nad receivers, the vfd will also show “volume up” or “volume down” or “volume: _ _ db” (_ _ indicates the numerical db level) while pressi...
Page 12
Tuner control (use with compatible nad receiver, am/fm/dab tuner models) set the device selector to “tun” in order to gain access to these buttons. Refer to the corresponding labels printed in the remote control faceplate and their respective assigned buttons to make use of these functions. Some of ...
Page 13
Library the avr 4 can store a different library of default nad codes for each of its device selector “pages.” if the original default library does not control your nad cd player, dvd player, or other component, follow the procedure below to change the library code. Refer as well to the table below f...
Page 14
Alternate ir channel the t 758 has the capability to operate via alternate ir channel. This is practically useful if you have two nad products that can be operated by similar remote control commands. With alternate ir channel, two different nad products can be controlled independently in the same zo...
Page 15
About the on-screen display (osd) the t 758 employs a simple, self-explanatory system of on-screen display “menus” that will appear on the connected video monitor/tv. These are required during the setup process (and are useful in day-to-day operation), so be sure to connect the monitor/tv before pro...
Page 16
Zone controls depending on the settings made at the separate “zone setup” menu under the “setup menu” section discussion, zone 2 can be configured and managed via this “zone controls” window. Set “power” to “on” to activate zone 2. When activated, the source input for zone 2 can be allocated by sele...
Page 17
Setup menu the setup menu allows one to customize the operation of the t 758 to the ancillary equipment used in one’s specific av system. Unless your system exactly matches the factory defaults as shown in the accompanying quick start guide, you will need to use the setup menu to configure the input...
Page 18
When devices that support hdmi control (cec) are connected, the following modes of operation can be executed via the t 758 or the external device using any of the device’s remote control. Off: applies to all cec options below. At “off” setting, particular cec feature is defeated. Power off: at “on” ...
Page 19
Analog audio the t 758 has six analog audio inputs including 7.1 input. These analog inputs - stereo 1, stereo 2, stereo 3, stereo front, media player (front) and external 7.1 can be variably assigned to each source. Scroll to “analog audio” and then press [ s ] and then [ d/f ] to select and assign...
Page 20
Speaker setup after connecting all ancillary sources and other combinations, the speaker setup menu will guide you on how to manage and setup your speakers in order to achieve optimum sound acoustics in your listening environment. The following are the speaker setup menu sections. Important! Dirac l...
Page 21
Setting speaker levels at test mode while at “speaker levels” menu, press the avr 4 remote’s [test] key activating the t 758’s speaker levels balancing test signal. You will hear a “surf” sound as you step through your speakers (“test mode active” is shown beside the speaker setup heading), beginnin...
Page 22
Zone 2 setup the zone 2 feature allows one to simultaneously experience in a different zone of the house selected audio from any of the enabled sources as well as from front input and media player. Volume zone 2 have fixed and variable volume control. When set to “variable” and while at the “zone co...
Page 23
Listening mode setup the t 758 has various listening mode options and is mostly configurable. These are provided to reproduce a variety of sound effects depending upon the content of the source to be played. Listening modes the audio format as detected by the selected source can be automatically con...
Page 24
Listening modes the t 758 offers distinct listening modes, tailored for different types of recording or program material. With a two-channel (stereo) source, the following listening modes can be selected. Stereo output is directed to the front left/right channels. Low frequencies are directed to the...
Page 25
Dolby setup dynamic range control: you can select the effective dynamic range (subjective range from soft to loud) for playback of dolby digital soundtracks. For fully cinematic effect, always select 100%, the default. Settings of 75%, 50%, and 25% progressively reduce dynamic range, making soft sou...
Page 26
Front panel display setup the vacuum fluorescent display (vfd) and on-screen display (osd) can be shown in various ways by navigating through the parameters at the display setup menu. Note the configurations set forth at “display setup” are carried over whenever it is enabled during a/v presets sett...
Page 27
Sample procedure for setting up a/v presets 1 setup first your preferred settings for the following options (access them through their respective menu page). Listening mode setup: as per settings in the menu dsp options: 5ms tone controls: tone defeat: on display setup: set “line 2” to “listening mo...
Page 28
Bluos setup bluos is a music management software developed by nad’s sister brand, bluesound. Bluos adds bluos network and internet music streaming with advanced music management to the t 758. There are two bluos setup options – bluos upgrade and factory reset. Bluos upgrade select “yes” to initiate ...
Page 29
Condition possible causes possible solutions no sound from all channels . • ac power unplugged. • check ac cable connection and outlet. • power not switched on. • outlet has no power. • mute function is activated. • toggle [mute] button to deactivate mute function. No sound from some channels . • fa...
Page 30
General specifications power output stereo mode 110w (8 ohms within rated distortion) ihf dynamic power; 8 ohms 137w ihf dynamic power; 4 ohms 243w power output surround mode 7 x 60w total harmonic distortion at rated power im distortion at rated power damping factor, 8 ohms >60 input sensitivity an...
Page 31
31 english por tuguÊs fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ.
Page 32
Www .Nadelectronics .Com ©2017 nad electronics international a division of lenbrook industries limited all rights reserved. Nad and the nad logo are trademarks of nad electronics international, a division of lenbrook industries limited. No part of this publication may be reproduced, stored or transm...