NAIM SUPERUNITI - Quick Start Manual - page 4
SuperUniti Quick Start Guide
English
Full Superuniti installation and operational information can be found in the reference manual
available on line at www.naimaudio.com
2 Switching on and Getting Started
• Once all connections have been made, switch on SuperUniti using the rear panel
mains switch
. SuperUniti will display a welcome screen and select its
Analogue 1
input.
Note:
If SuperUniti is left unused its display will switch off after a preset time. The “Auto-off” time
can be adjusted within the setup menus.
• The SuperUniti display language can be changed. Enter setup mode by pressing the
handset
setup
( ) key, select the language option and use the handset
up
(
5
)
and
down
(
6
) keys to select the desired language. Press the
ok/list
key to confirm the
selection. Leave setup mode by pressing the
exit
key.
• SuperUniti is configured when shipped to connect to wired
TCP/IP networks
automatically. However, if your SuperUniti has been previously used and its network
configuration altered, or your router requires nonstandard settings, it may not be able
to do so. Refer to the Reference Manual if this appears to be the case.
If a wireless network connection is to be used, SuperUniti will require configuration to
join the network. Press the handset
setup
( ) key once SuperUniti is switched on and
select the
Network Settings
option to configure the SuperUniti wireless settings. Refer to
the Reference Manual for more information if necessary.
• If a subwoofer or external power amplifier is to be used, the SuperUniti
Preamp
and
Sub
outputs must be configured from the
Speakers
setup menu. Press the handset
setup
(
) key and select
Speakers
followed by
Amp Used
. Select
External
if an external power
amplifier is to be used. Select
all outputs
if the SuperUniti internal amplifier and a
subwoofer or an additional external amplifier are to be used. Select
internal only
if only
the SuperUniti internal amplifier is to be used.
• If SuperUniti is to be used with an external DAC, the SuperUniti digital output must
be activated from the
digital output
setup menu. Press the handset
setup
( ) key and
select the
digital output
option.
• To adjust SuperUniti volume use either the front panel
volume control
or the handset
vol-
and
vol+
keys. The numeric volume value is shown in the top left corner of the
SuperUniti display.
3 Selecting Inputs
• SuperUniti inputs can be selected by pressing the front panel
input
button, the handset
up
(
5
) and
down
(
6
) keys or one of the handset
input selection
keys.
• Pressing one of the handset
input selection
keys either selects a single input or scrolls
through a group of inputs. For example, pressing the
PC
key selects the
UPnP
input,
while pressing the
radio
key scrolls through a group comprising the
Fm, daB
and
iRadio
inputs. The default input selection key assignments are described in the Reference
Manual. To modify the key assignments press the handset
setup
( ) key then select
the
Handset Buttons
option.
• When SuperUniti is connected to a network with high speed internet access it will
automatically download a list of available internet radio stations. When the
iRadio
input is subsequently selected, a menu will be displayed that lists all the available
stations sorted by location and genre. Use the handset
up
(
5
),
down
(
6
),
left
(
3
) and
ok/list
keys to browse the list and select stations.
Internet Radio
3/8
Added stations
Naim’s Choice
4
Location
Genre
Inputs On: radio
1/4
4
1. FM
2. DAB
3. iRadio
4. Unassigned
Note:
The n-Stream app,
available from the iTunes App
Store, enables wireless touch
screen control of SuperUniti
from an iPhone or iPod touch.
Setup
1/9
4
Language
Inputs
Speakers
Headphones
Network Settings
1/5
4
Name:
Super-C2E6
Wireless:
Not Used
Status: Not Connected
DHCP:
Yes
Speakers
1/3
4
Amp Used: Internal Only
Max. Volume:
100
Balance:
0