- DL manuals
- NAPCO
- Security System
- Gemini GEM-X255
- Programming Instructions Manual
NAPCO Gemini GEM-X255 Programming Instructions Manual - page 49
L
NAPCO Security Systems
X
GEM-X255 Programming Instructions
WI1092B 9/02
!
Page 49
SYSTEM RESET OPTIONS (ADDRESS 4091-4093)
Clear Dealer Program (Erases Dealer Program)
This erases the dealer program. Use this feature to start a
customized default program.
Access address 4091, then press the
J
button. Data entry is not allowed.
NOTE: Enter Easy Menu Driven Program Mode to program system again.
GEM-RP1CAe2 Keypad
4091 XX
GEM-RP2ASe2 Keypad
4091XX
Cold Start (Erases Entire Program)
This erases the entire program (codes, schedules, foreign
language configuration, etc), leaving the panel as it came
right out of the box.
Access address 4093, then press the
J
button. Data entry is not allowed.
NOTE: Some features (schedules, language configuration) can only be
re-programmed with the Downloading Software.
GEM-RP1CAe2 Keypad
4093 XX
GEM-RP2ASe2 Keypad
4093XX
Sy
stem Reset Options
Summary of Gemini GEM-X255
Page 1
R programming instructions hardwire wireless g e m - x 2 5 5 control panel/communicator w1092b 9/02 © napco 2002 quick start: 1. Refer to the wiring diagram, connect the keypad(s), siren, aux. Power, aux. Output, remote bus, earth ground, zone and telephone wiring. Note: see installation instruction...
Page 2
Napco security systems, inc. 333 bayview avenue, amityville, new york 11701 for sales and repairs, call toll free: (800) 645-9445 for direct line to technical service, call toll free: (800) 645-9440 internet: http://www.Napcosecurity.Com gem-x255 notes: ! F or a gem-x255 system comprising 96 zones o...
Page 3
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 3 system programming options .............................4 introduction ..................................................................4 downloading from a computer ....................................4 easy menu dr...
Page 4
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 4 system programming options introduction the gem-x255 control panel may be programmed by various means, each of which will be covered in detail in the sections that follow. Keypad displays shown are for a gem-rp1cae2 (...
Page 5
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 5 easy menu driven program mode dealer program - preliminary information ! Only keypad #1 may be used for both dealer and user programming, however this keypad may be located in any area. ! The master security code is p...
Page 6
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 6 gem-rp1cae2 keypad: z ones per area, fire zo nes, 2-wire fire zo nes & cs rep o rting a. Gem-rp1cae2 keypad to create your customized default program using a gem-rp1cae2 keypad, enter the following parameters. In each...
Page 7
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 7 exit/entry zones (appears for new panel only) directly enter the zone numbers which are to be used as exit/entry zones. Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros. Use nu...
Page 8
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 8 central station receiver 1 account number enter an account number of up to four digits. Use number buttons 1 through 9 for digits 1–9. Note: press the 0 button for a zero and press the g 0 buttons for a blank space (•...
Page 9
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 9 gem-rp1cae2 ke yp ad : use r codes enter user codes (press the ( a ) button to set cursor.) enter up to 195 user codes with user options, authority level and access control options (if necessary) for each code. Refer ...
Page 10
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 10 ! Press j to save each code. To proceed to the next user code, set the cursor to the user number and change it using the number buttons. Program a new user code as previously described. Press next ( e ) button to pro...
Page 11
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 11 rf transmitter points (press the ( a ) button to set cursor.) (for wireless systems only. Also see quick method, which follows) for each transmitter (key fob transmitters also), enter the zone number (01–96) to which...
Page 12
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 12 key fob transmitters (press the ( a ) button to set cursor.) keyfobs can be programmed as “arm/disarm” devices.(refer to wi752). For each key fob transmitter, enter: ! The key fob transmitter number (01–16). ! Area n...
Page 13
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 13 enter time (press the ( a ) button to set cursor.) enter the current time in the format hh:mma/p, where hh=hours (01–12); mm=minutes (00–59). Select am or pm by pressing any number button, then press j once again to ...
Page 14
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 14 accessing direct addr ess program mode direct address program mode display & commands 0000 3c 0 0 0 0 3 c ( s e c o n d s ) 1 2 = data entry location (left and right 2 = address 1 1. Press eeeeee a 2. Press g until “...
Page 15
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 15 the displays shown on the previous page will appear after a brief delay. ! Use the the a button to toggle the cursor between the 4-digit address field and the data entry locations. ! Enter the address directly using ...
Page 16
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 16 direct address programming example example: program zones 6, 7 and 8 as exit/entry follower zones. Determine the data entries ! 1. Referring to zone features in the programming worksheets that follow, exit/entry foll...
Page 17
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 17 programming options & worksheets r computerized security system gemini armed sta tus system armed 01/01/97 12:00am 1 2 4 3 5 6 7 8 9 0 a b c d e f g next/yes prior/no area # of zones in area 1 enter # zones x x ai #z...
Page 18
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 18 r computerized security system gemini armed stat us system armed 01/01/97 12:00am 1 2 4 3 5 6 7 8 9 0 a b c d e f g next/yes prior/no area # of zones in area 1 enter # zones x x ai #zn=08 #kp=1 a2 #zn=00 #kp=0 this p...
Page 19
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 19 system delays & timeouts (address 0000-0002, 2402, 2406, 2414 & 3902) address 0000 left right exit delay (sec.) [default = 3c] address 0001 left right entry delay 1 (sec.) [default = 1e] address 0002 left right entry...
Page 20
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 20 [default = blank (•) blank (•) from address 0490-0492] system delays & timeouts (address 2400, 2401, 2403-2405, 4082 & 4083) data entries left right blank (•) blank (•) blank (•) 1 blank (•) 2 blank (•) 3 blank (•) 4...
Page 21
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 21 default for cs receiver 1 format depends on easy menu question “rcvr format”. [default = •(blank) •(blank)] for cs receivers 2 and 3 formats. Cs receiver format options (address 0520, 0521, 0525, 0526, 0550, 0551, 05...
Page 22
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 22 cs receiver 1 telephone number (digits 1-20) address 0527-0546 (right digits 1-20) 0527 0528 0529 0530 0531 0532 0533 0534 0535 0536 0537 0538 0539 0540 0541 0542 0543 0544 0545 0546 r r r r r r r r r r r r r r r r r...
Page 23
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 23 cs subscriber id numbers (address 0650-0787) cs subscriber id nu mbers (telco 1 & 2) area 1 address 0650-0653 (right digits 1-4) 0650 0651 0652 0653 r r r r cs telco 1 subscriber opening/closing id numbers area 2 add...
Page 24
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 24 cs reporting codes (address 0859-0869) address 0864-0869 left addr right blank (•) 0864 blank (•) 0865 blank (•) 0866 blank (•) 0867 0868 0869 opening/closing reporting codes closing conditional closing opening openi...
Page 25
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 25 cs reporting codes: ! 1. Enter in corresponding address location (left and right digits). ! 2. Valid entries are: 1-9, 0 and b-f. Note: dark shaded data value box shows option not available. Address 0870-0880 left ad...
Page 26
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 26 address 0910-0917 zones report code (control panel) zone 1 zone 2 zone 3 zone 4 zone 5 zone 6 zone 7 zone 8 0910 0911 0912 0913 0914 0915 0916 0917 l r l r l r l r l r l r l r l r address 0918-0921 zones report code ...
Page 27
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 27 cs user reporting codes (address 1030-1055) user opening telco 1 address 1042 left right blank (•) right data values user 00 user 99 user 98 user 97 8 4 2 1 user 197 = auto arming/disarming user 198 = quickloader arm...
Page 28
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 28 cs user reporting codes (address 1056-1081) user opening telco 3 address 1068 left right blank (•) right data values user 100 user 99 user 98 user 97 8 4 2 1 user 197 = auto arming/disarming user 198 = quickloader ar...
Page 29
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 29 global sy stem trouble reporting options global system trouble reporting options (address 1082-1116) [default = blank (•) blank (•) from address 1082-1092] system response activated by global event/trouble burglary a...
Page 30
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 30 ar ea sy stem tr ouble re por ting options area system trouble reporting options (address 1120-1157) ! 1. Select the desired option by circling " the data values for each digit (left and right). ! 2. Add the data val...
Page 31
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 31 area system trouble reporting options (address 1160-1197) ! 1. Select the desired option by circling " the data values for each digit (left and right). ! 2. Add the data values (ex: 15=1+2+4+8) from the selected opti...
Page 32
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 32 zone options / zones 1-16 (address 1200-1386) zone options 50ms loop response (a) 20ms loop response (a) priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warn...
Page 33
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 33 ! 1 ! ! 4 ! 4 ! 2 ! 2 ! 2 zone options / zones 17-32 (address 1402-1586) r zone options priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warning never arm 24-...
Page 34
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 34 ! 1 ! ! 4 ! 4 ! 2 ! 2 ! 2 zone options / zones 33-48 (address 1602-1786) zone options priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warning never arm 24-ho...
Page 35
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 35 ! 1 ! ! 4 ! 4 ! 2 ! 2 ! 2 zone options / zones 49-64 (address 1802-1986) zone options priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warning never arm 24-ho...
Page 36
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 36 ! 1 ! ! 4 ! 4 ! 2 ! 2 ! 2 zone options / zones 65-80 (address 2002-2186) zone options priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warning never arm 24-ho...
Page 37
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 37 ! 1 ! ! 4 ! 4 ! 2 ! 2 ! 2 zone options / zones 81-96 (address 2202-2386) zone options priority priority with bypass auto-bypass selective bypass keyswitch arming auto-bypass re-entry pre-alarm warning never arm 24-ho...
Page 38
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 38 ! 1. Select the desired zone option. Zone options 50ms loop response 10ms loop response priority priority with bypass auto-bypass ! 2. Enable desired options for each zone by drawing a circle " around its correspondi...
Page 39
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 39 [default = blank (•) blank (•)] [default = blank (•) blank (•)] [default = blank (•) blank (•)] system options (address 2415-2419) address 2415 left digit (sum of data values) right digit (sum of data values) system ...
Page 40
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 40 system options (address 2420-2422, 3874 & 3879-3881) [default = blank (•) blank (•)] address 2420 left digit (sum of data values) right digit (sum of data values) system options disable keypad instant button enable l...
Page 41
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 41 system options (address 3882-3901, 3903-3905 & 4084) ! 1. Select the desired option by circling " the data values for each digit (left and right). ! 2. Add the data values (ex: 15=1+2+4+8) from the selected options. ...
Page 42
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 42 this page intentionally left blank.
Page 43
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 43 right blank (•) 1 2 3 4 5 6 7 8 option not used area 1 area 2 area 3 area 4 area 5 area 6 area 7 area 8 keypad area assignment keypad options: select options for any of the 15 keypads. * note: for remote access contr...
Page 44
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 44 [default = blank (•) blank (•) from address 2500-2595] user area options (address 2500-2595) s ! 1. Select the desired user number. User no. 1 2 3 4 5 ! 2. Enable desired areas for each user by drawing a circle " aro...
Page 45
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 45 ezm group options (address 2600-2621) default depends on easy menu question “# of zns in area1” and “# of zns in area2”. For example, if 96 zones are used, then all 22 groups will be automatically enabled. If only 8 ...
Page 46
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 46 area arming options (address 2650-2657) priority area arming: ! 1. Select the desired arming area. ! 2. Enable desired options for each priority area by drawing a circle " around its corresponding binary data value. ...
Page 47
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 47 area output control options (address 2700-2739) area output turns off upon disarm: select options for any of the 5 outputs per area when disarming a particular area. ! 1. Select the desired option by circling " the d...
Page 48
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 48 rf receivers & supervisory timer options (address 3776 & 3760-3775) default for number of receivers depends on easy menu question for rf transmitters. Address 3776 left right blank (•) number of rf receivers data ent...
Page 49
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 49 system reset options (address 4091-4093) clear dealer program (erases dealer program) this erases the dealer program. Use this feature to start a customized default program. Access address 4091, then press the j butt...
Page 50
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 50 user program mode preliminary information the user program mode is covered in detail in the operating instructions for the keypad in use. ! Only keypad #1 may be used for programming, however this keypad may be locat...
Page 51
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 51 zone descriptions enter an identifying description for each zone. Buttons 1 and 2 set the cursor position; buttons 3 and 6 scroll numbers, letters, punctuation marks, etc. ! Position the cursor over the displayed zon...
Page 52
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 52 keypad configuration mode this section will focus on configuring the gem-rp1cae2 and gem-rp2ase2 keypads. If there is more than one keypad in the system, only keypad no. 1 may be used for programming. Keypad installa...
Page 53
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 53 compatibility number the compatibility number is a 4-digit security code that, if programmed into both the control panel and each gem-rp1cae2 keypad, dedicates the keypad to only that panel. That is, (a) similar keyp...
Page 54
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 54 keypad programming modes note: ! 1. Functions that are not active, not programmed and/or not applicable to user’s authority level will be suppresses and will not display. ! 2. Many functions will not be displayed (su...
Page 55
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 55 keypad commands 1 2 4 3 5 6 7 8 9 0 a b c d e f g next/yes prior/no area scroll down scroll up exit yes no enter dealer code function level (a) display zn faults 1 display zn bypassed 1 display zn directory 1 active ...
Page 56
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 56 keypad commands 1 2 4 3 5 6 7 8 9 0 a b c d e f g next/yes prior/no area set cursor exit yes/ scroll down no/ scroll down execute function area 1 # of zones (e) area 2 # of zones (e) fire zone numbers 2 wire fire zon...
Page 57
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 57 keypad commands 1 2 4 3 5 6 7 8 9 0 a b c d e f g next/yes prior/no area scroll down/ set cursor scroll up exit yes no execute enter user code function level (a) display zn faults 1 display zn bypassed 1 display zn d...
Page 58
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 58 keypad configuration mode gem-rp1cae2 keypads press a button enter factory code: 11123 configure: • keypad beep on/off • entry sounder • keypad address 01 • new compat# 000 ** • ezm address 00 • zone response 00 • pr...
Page 59
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 59 programming options index programming option program mode address location page number 10ms loop response direct address 1201 32 - 37 1400hz handshake/kissoff direct address 0526,0551 & 0576 21 2300hz handshake/kisso...
Page 60
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 60 pr ogrammi ng opt ions inde x programming option program mode address location page number cs receiver 3 format direct address 0575 21 cs receiver 3 options direct address 0576 21 cs receiver 3 telephone number direc...
Page 61
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 61 programming option program mode address location page number exit delay direct address 0000 19 exit/entry follower (zone option) direct address 1218, 1318, 1418, . . ., 2318 32 - 37 ezm group options direct address 2...
Page 62
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 62 programming option program mode address location page number sensor watch (zone option) direct address 1240, 1340, 1440, . . ., 2340 32 - 37 sensor watch delay direct address 4088 19 service message report code direc...
Page 63: Gemini Gem-X255
L napco security systems x gem-x255 programming instructions wi1092b 9/02 ! Page 63 gem-x255 wiring diagram gem-x255 wiring diagram gemini gem-x255 w i1093 ge m- x2 55 w i1093 r c o m p u t er iz ed s e c u r it y sy st em gemini arm e d s t at us syste m a r m e d 01 / 0 1/ 9 7 1 2 :00a m 12 4 3 56...
Page 64
X gem-x255 programming instructions l napco security systems wi1092b 9/02 ! Page 64 napco security systems, inc. (napco) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. Napco will, within said period, a...