Sectional and tilting door opener installation instructions and user guide sdo800 warning please read the manual carefully before installation and use. The installation of your new door opener must be carried out by a technically qualified or licensed person. Attempting to install or repair the door...
Contents important safety recommendations.. …………………………….………………………….….1-2 basic function introduction ………..……………………………………………….……………...2 special function introduction ………….…………………………………………………………..2 installation (aluminum track) ………………………………………….…………………………..3-4 installation (steel track) ……………………………………...
1 important safety recommendations failure to comply with the following safety recommendations may result in serious personal injury, death and / or property damage. 1. Please read carefully and adhere to all safety and installation recommendations. 2. The opener is designed and manufactured to meet...
2 - frequently examine the installation, in particular check cables, springs and mountings for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. - each month check that the drive revers...
3 referring to fig. 2 for recommended installation 1) aluminum track 5) inside panel 2) 24v dc flashing light (optional extra) 6) power socket 3) push button 7) door opener 4) photo beam (rx/tx type) chain shuttle assembly as for the ease of the chain, it is delivered with the chain and chain shuttl...
4 fig. 6 fig. 7 before attaching the motor brackets (e) (fig 4) screw an inverted nut (6mm) (d) on each stud then position the brackets (e) on the studs and secure them in-place using a second 6mm-nut and then lock the brackets to the rail by tightening the inverted lock nuts (d).Fix the opener to t...
5 installation (steel track) fig. 1 fig. 2.
6 1. Fixing the track bracket. Fixing the track bracket to the wall 2cm-15cm over the shaft or intermediate bracket (depend on the actual installation space). 2. Fixing the steel track to the bracket with cotter pin a. (fig. 1) 3. Fixing garage door opener to the track by u hanging bracket a. It ‟s ...
7 installation recommendations remember there are specific standards that have to be strictly followed regarding the safety rules of electrical installations and automatic gates and doors. As for the legal requirements and standards that must be adhered to, please take notice of the following points...
8 basic function setting and applying 1. Itinerary setting opening & closing force self-learning 2. Matching the receiver and transmitter fig. A fig. B press „set‟ button and hold on until the led displays figure „1‟, then adjust the up limit by pressing „lim-1‟ button. Fine- tuning „lim-1‟(up) or „...
9 3. Safety reverse force adjustment 4. Auto-close setting 5．photo beam setting 6. “k” - button press „set‟ button and hold on until the led displays „3‟. It‟s under force adjustment mode. Press „lim-1‟ button to increase the force and „lim-2‟ button to decrease the force. The maximum force is 9 and...
10 fig. 1 fig. 2 special function introduction and application the following functions are made to order in accordance with the special needs of customers: 1．the o/s/c button function add an o/s/c button to open or close the door. 2．auto safety reverse function this special function is for safety co...
11 aluminum track accessories list name amount clutch components ×1 hanging bracket ×1 motor bracket ×2 φ6×90 axis pin ×1 φ8×55 carriage bolt ×2 bracket for door panel ×1 bracket for track ×1 clutch cord ×1 cord pendant ×1 φ1.8×38 cotter pin ×2 φ6×14 bolt ×8 φ8×16 h exagon head bolt ×2 φ8×25 axis pi...
12 manual disengagement the opener is equipped with a manual release cord to disengage shuttle and move door by hand while holding the handle down (fig 12). Pull on the handle to disengage the shuttle. To re-engage the door simply run opener in automatic mode or move door by hand until the trolley e...
13 technical specifications power input: 140w (800n) 220 - 240 v ac 50 hz or 110 -120 v ac 60 hz (subject to customer ‟s area) motor: 800n: 50w light time: 3 minutes working temperature: -20° ~ 40°c relative humidity: open and close force: 800n reception frequency: 303 mhz or according to customer ‟...
73-75 magnesium drive, crestmead qld 4132 ph: (07) 3803 7600 fax: (07) 3803 7611 email: enquiries@napoleongd.Com.Au web: www.Napoleongd.Com.Au.
