Northern Computers N-750 Configuration manual - page 18
14
Version 1.0
October 1997
N-750 Configuration Guide
N-750-GSM:
The N-750-GSM is for a ground start
telephone system, and consists of a ground start
chip. Please note that a ground start module
cannot be used in UL applications.
N-750-INPT-CNCT:
The N-750-INPT-CNCT is a
connector that plugs into the N-750-PAIT. This
allows for the input zones and output relay of the
N-750-PAIT to be connected. One unit comes
standard with each N-750-PAIT.
N-750-KOHP:
The N-750-KOHP provide tamper
proof hole plugs for the N-750 enclosure. The N-
750-KOHP comes in a pack of 6 UL approved
knock out hole plugs.
N-750-PAIT:
The N-750-PAIT is a commercial
touchpad that can be used as a door access
station. The N-750-ADM can be used in conjunc-
tion with the N-750-ADM for a total combination
of 24 devices. The N-750 system must have at
least one N-750-PAIT. The N-750-PAIT has 1
SPDT relay for door lock and 2 contact inputs for
door egress and status. The touchpad can also be
used to program the system in addition to arming
and disarming alarms and checking the status of
areas.
N-750-PI:
The N-750-PI Serial/Parallel Module
provides one 9 pin RS-232 serial port and one
parallel printer port. Eight N-750-PIs can be used
per N-750. The N-750 can be used for either
connection to a PC directly using the CBL-N-750
or in conjunction with an M-9600 and CBL-2 for
remote communications.
N-750-RDR-CNCT:
The N-750-RDR-CNCT is a 5
wire Wiegand connector that plugs into the N-
750-PAIT. This allows a Wiegand format reader to
be plugged directly into the N-750-PAIT. One unit
comes standard with each N-750-PAIT.
N-750-SK:
The N-750-SK upload/download soft-
ware is for programming the N-750 system by the
installing dealer or central station. The software
programs partitions, zones, time windows, user
levels, system devices, and central station report-
ing accounts. Only one copy is required per
dealer. Each copy can support an unlimited
number of panels.
N-750-SLTP:
The N-750-SLTP is an indoor/outdoor
touchpad with weather resistant housing. The N-
750-SLTP can be used to arm/disarm an N-750
system as well as used for door access as entry
only or in conjunction with a card reader for high
security with a combination card and pin number.
The touchpad has “READY” and “Armed” lights,
but there is no display screen. The N-750-SLTP
must be interfaced with the N-750-ADM. Current
Draw: 10 mA, Temp: 32 to 120 F (0 to 49 C),
Dimensions: 1.5"W x 6.37"H x .5"D.
N-750-SS:
The N-750-SS SmartSensor is used in
conjunction with the N-750-SSE. The N-750-SS
connects to serial loops on the N-750-SS control-
ler module. N-750-SS SmartSensor point ID
modules allow connection to and point identifica-
tion of, most security devices. SmartSensor point
ID modules are addressed on-site using an N-750-
PAIT.
N-750-SSE:
The N-750-SSE Serial Zone Expander is
a UL listed zone expansion system. The N-750-
SSE is used in conjunction with the N-750-SS
Smart Sensor. Each N-750 system can support a
total of 3 N-750-SSE expanders for a total of 384
points, with 128 points per N-750-SSE. Each point
on the N-750-SSE is addressed with an N-750-SS.
The N-750-SS does not have a built-in end-of-line
resistor, and the N-750-EOL-UL-SS resistor should
be used for all UL Smart Sensor applications.
N-750-TC:
The N-750-TC transformer cover is a UL
rated outlet cover for a standard duplex outlet.
The N-750-TC is required for NFPA 71 and NFPA
72A fire alarm installations to protect class 2
transformer and power wiring to N-750 control.
Knockouts provided for 3/4" conduit. Dimensions:
3.625" W x 6.125"H x 2.5"D.
N-750-ZONE:
The N-750-ZONE is a hardwire
expander that allows 64 zones to be added to the
N-750 system. A total of six N-750-ZONE mod-
ules can be added to the system (if no other zone
expansion device is being used).