1. DL manuals
  2. Oasis
  3. Water Dispenser
  4. Aquabar 2
  5. Use & Care Manual

Oasis Aquabar 2 Use & Care Manual

Summary of Aquabar 2

  • Page 1

    Use & care guide premium point-of-use water cooler table of contents use & care guidelines & features ........................................................2 electrical power requirements ..............................................................3 leak controller instructions.....................

  • Page 2

    2 installing the water cooler determine the best installation location. Consider customer preference, electrical outlet, and cold water line access. Warning: a pressure regulator must be installed in front of the unit’s water inlet if the water pressure (including any possible pressure spikes) could...

  • Page 3

    3 the electronic display if desired. The uv bulb should be replaced every year to maintain the effectiveness of the bulb and the quartz sleeve should be cleaned for proper transmittance. To replace the bulb, remove the cooler top and disconnect the wire harness. Remove the 4 screws on top of the uv ...

  • Page 4

    4 7. Snap the plastic sensor connector onto the plastic base in the location marked in figure 2. The clip snaps over the rib on the outside of the base so that the terminals in the plastic housing are inside the base. 8. Open the valve again. Now the controller is ready to sense any water. Note: the...

  • Page 5

    5 7. To install the carbon filtration system, cut the blue tube which is looped in the filter compartment. Cut it so you have enough tubing to connect your filter inlet and outlet without making the tubes too tight. 8. Connect your filters and turn on water to flush filter(s) per the manufacturer’s ...

  • Page 6

    6 set the clock 3. Press the “clock set” button once; the hour will flash. 4. Use (+) or (-) button to set hour. Make sure am or pm setting is correct. 5. Press the “clock set” button again; the minutes will flash. 6. Use (+) or (-) button to set minutes. 7. Press the “clock set” button again; the d...

  • Page 7

    7 14. Use the (+) button to move forward from weekdays to saturday/sunday and the (-) button to move back to the weekdays. It does not roll over from saturday/sunday to monday through friday. Note: the beginning and ending time for weekdays and weekends must be set individually. This means the proce...

  • Page 8

    8 31. Use the (+) or (-) button to set the total number of months you wish to monitor up to. The maximum number you can enter is 12 months and it does not roll over to 0 after this value. Hold down the (+) or (-) button to roll through the numbers. 32. To turn the uv bulb monitor on or off, hold the...

  • Page 9

    9 2. Use mild soap and water to clean the surfaces. Rinse thoroughly with clean water. Do not use harsh or abrasive cleaners to clean the cooler. 3. Sweep away or vacuum any dust from the condenser coils on the back of the unit. 4. Wash the drip tray in soapy water. Do not place in dishwasher. To re...

  • Page 10

    10 of the taller ear should line up with the hole for the uv bulb. You don’t need to sanitize the cooler unless you wish to. If you have a tri-temp model, you will also need to reconnect the vertical silicone tube to the stainless steel hot tank tube. Put the side panel back on, then place the cabin...

  • Page 11

    11 17. Let the reservoir and the hot tank (if applicable) fill. After 5 minutes, check to see that water flows easily from all taps (see hot water safety instructions on page 3). Important: you must wait until water has filled the hot tank before plugging in the cooler to avoid overheating. You can ...

  • Page 12

    12 12. To put the center front panel back in, slide the bottom tabs over the lip on the alcove piece. Rotate the top in, snapping the top tabs into the front panel. Due to the close fitting parts, you get a smoother look if you press the top of the center front panel in place before snapping the two...

  • Page 13

    13 water cooler troubleshooting water cooler leaks on the inside unplug water cooler and turn off water supply immediately. Wipe up any water on the floor. Call customer service. Lcd models: set cold control to colder or coldest. If water is not colder after 2 hours, call customer service. Water is ...

  • Page 14

    14 leak controller troubleshooting * please note that whenever the valve closes to the red position (except when testing), you must do the following: 1. Change the batteries 2. Check and test the sensor and controller 3. Look for leaks. It is possible that you had a leak and it has dried. Condition ...

  • Page 15

    15 owner’s copy 3 year water cooler limited warranty first year: the manufacturer promises the original purchaser (user) to repair or, at the manufacturer’s option, to replace any part of this water cooler which proves to be inoperative due to a defect in material or workmanship under normal use, fo...

  • Page 16

    Oasis international 222 e. Campus view blvd • columbus, oh 43235 u.S.A. 1-800-64-oasis (1-800-646-2747) www.Oasiscoolers.Com printed in china ©2010 oasis international 031666-019 rev. B.

  • Page 17

    Uv bulb install in aquabar 2 1. Remove 2 screws from back of unit top. 2. Lift off top to expose ss reservoir lid. 3. Lift ss lid up and remove silicone plug (it’s now red). Screws for cabinet top silicone plug step 1 2 3 4. The reservoir baffle is shipped in a bag inside the filter compartment. Rem...

  • Page 18

    Uv bulb install in aquabar 2 7. Remove two screws at rear of right side panel (when facing unit). 8. Remove two screws at front of right side panel. 9. Lift side panel up slightly (about 1”) and slide away from unit. If panel hangs up, lift it a little higher or let it drop slightly. Panel should co...

  • Page 19

    14. Line up top mounting hole with notch on ballast. Insert 2 nd screw and tighten just until snug. Overtightening will crack ballast housing. 15. Insert insulated male tab into insulated female terminal. Match white wire to white wire and black wire to black wire. 16. Route wire harness with red an...

  • Page 20

    Uv bulb install in aquabar 2 21. Return cabinet top to unit, starting it at back and lining up sides. 22. Slide your hand over one “finger” at a time near the front to work the snap into place. You will feel and hear it snap when it is properly located. The side may slip to the outside of the side p...