Oasis Aquabar 2 Use & Care Manual - page 6
6
SET THE CLOCK
3. Press the “CLOCK SET” button
once; the hour will flash.
4. Use (+) or (-) button to set hour.
Make sure AM or PM setting is
correct.
5. Press the “CLOCK SET” button
again; the minutes will flash.
6. Use (+) or (-) button to set
minutes.
7. Press the “CLOCK SET” button again; the day of the week will flash.
8. Use the (+) button to move forward through the days of the week and the (-) button to move backwards. Note the
days do not roll over from Sunday to Monday or vice versa. After 10 seconds of no action or when the “CLOCK
SET” button is pressed again, the “CLOCK” mode ends and the clock will begin running.
HOT WATER TEMPERATURE SET MODE
9. Press the “TEMP SET” button, and the HOT CUP ICON will begin flashing. The word “OFF” appears next to the
CUP.
10. Press (+) or (-) button to set the hot water temperature from “OFF” to “HOT” (about 165ºF) to “HOTTER” (about
180ºF) to “HOTTEST” (about 194ºF). NOTE: Each time the (+) button is pushed, the temperature display
advances and lights up an additional temperature bar up to “HOTTEST.” The next time the (+) is pushed, the
“OFF” will light up and all the bars will be turned off. Press the button again and the “HOT” bar lights, the “OFF”
goes out. It is a continuous loop that the button advances through – either forward or backward depending if the
(+) or (-) button is used. By setting the hot tank to “OFF,” your water cooler will dispense room temperature water
instead of heated water when the hot water button is pressed.
COLD WATER TEMPERATURE SET MODE
11. When done setting the hot water temperature, press “TEMP SET” again and the COLD SNOWFLAKE ICON will
begin flashing. The word “OFF” appears next to the SNOWFLAKE.
12. Press (+) or (-) button to set the cold water temperature from “OFF” to “COLD” (about 50ºF) to “COLDER” (about
45ºF) to “COLDEST” (about 40ºF). NOTE: Each time the (+) button is pushed, the temperature display advances
and lights up an additional temperature bar up to “COLDEST.” The next time the (+) is pushed, the “OFF” will
light up and all the bars will be turned off. Press the button again and the “COLD” bar lights, the “OFF” goes out.
It is a continuous loop that the button advances through – either forward or backward depending if the (+) or (-)
button is used. By setting the cold temperature to “OFF,” your water cooler will dispense room temperature water
instead of chilled water when the cold water button is pressed.
SETTING THE ENERGY SAVER MODE
The “ENERGY SAVER” mode is designed to save energy during a period of time each day by turning off the compressor
and the hot tank for the time you specify. For example, if you do not plan to use your water cooler at night or on weekends,
you may want the ENERGY SAVER mode to run from 10:30 PM to 6 AM on weekdays and off all weekend.
Weekdays are signified by MTWTF and the weekend is signified by SaSu. All weekdays will use the same start and end
time, and Saturday and Sunday will share a start and end time. Note that if the cooler is on energy saver mode at midnight
Friday, it will stay in energy saver mode until the start or end time of Saturday/Sunday is reached. At that point it will switch
over to the start/end time for the weekend. The same is true at midnight Sunday when it waits for the start/end time of
Monday through Friday.
Note: To turn the cooler off all weekend, set the end time one minute after the start time for Saturday/Sunday.
13. Press the “ENERGY SET” button and the days of the week will flash and the words “ENERGY SAVER” will light
up.
Figure 5