- DL manuals
- Officezone
- Binding Machine
- RHIN-O-TUFF OD 3500
- Instruction Book
Officezone RHIN-O-TUFF OD 3500 Instruction Book
Summary of RHIN-O-TUFF OD 3500
Page 1
Allpdi punches feature easily removable 1-800-543-5454 www.Officezone.Com officezone.
Page 2
The o d 4000 punch with od 4300 plastic the od 4000 punch with o d 4300 plastic coil inserter module and the od 4200 coil inserter module and the od 4400 wire closer module comb opener module the hd 7500 24 inch heavy duty punch the hd 7000 14 inch heavy duty punch the hd 6500 14 inch heavy duty pun...
Page 3: Table of Contents
Table of contents optional od 3500 combo binding station, modules & accessories topic page number combo binding station & modules 3&4 1) attaching coil inserter module setup instructions a) determine the correct coil size b) determine the correct size mandrel c) installing the mandrel on the machine...
Page 4
Topic page number diagram 3 wire closer 13 diagram 4a wire closer 14 diagram 4b wire closer 15 diagram 4c wire closer 16 diagram 4d wire closer 16 diagram 5 comb opener 17 diagram 6 comb opener 19 troubleshooting coil inserter module 11 electrical schematic coil inserter module 12 1-800-543-5454 www...
Page 5
Combo binding station the combo binding station is a base unit that supports three different binding modules. Each module attaches in a matter of minutes. The attachment procedure will be located in the module instructional section of this manual. Coil inserter the plastic coil inserter will bind bo...
Page 6
Wire closer the wire closer is capable of binding books up to 1-1/8" (28.6mm) thick. It uses wire sizes from 3/16 to 1 -1/4". It has an adjustable closing bar for the different size wires. Each end can be adjusted independently to obtain a perfect close. The unit attaches to the rear of the combo bi...
Page 7: Coil Inserter Module
Coil inserter module 1) installation instructions: diagram 1 procedure to attach the coil inserter onto the combo binding station or the od 4000 punch. + align the t w o threaded studs (1) that protrude from the coil inserter option into the two holes located on the right side of the combo binding s...
Page 8
Setup instructions: diagram 2a, 2b, 2c, 2d & 2e a) determine the correct coil size. Use a coil that is at least 3/32 (2.5mm) larger than the book thickness for coil sizes up to 3/4" (2omm). After 3/4”, use a coil size of at least 1/8" over the book size. The larger the coil compared to the book, ins...
Page 9
Diagram 2a a) adjusting the paper stop. Place the book on top of the combo binding station or the od 4000 punch with the right side of the book against the paper stop bracket. Adjust the paper stop (6) so the holes of the book hang over the edge of the combo binding station or od 4000 punch. The hol...
Page 10
Forward /off / reverse switch. The forward / off / reverse (8) switch has three positions. The center position of this switch is the off position and should be placed in this position when not using the machine. Press the left side (forward) of the switch and the coil will rotate into the book. Pres...
Page 11
Holes in the sheets or covers. Continue until the coil is past the left side of the book by about one or two coils. Diagram 2d i) drive wheel stop screw. The drive wheel stop screw (12) will prevent the wheel from pressing to hard on the mandrel. It is very important not to have too much pressure on...
Page 12
Diagram 2e edge of the right hand side of the book. Open the cutter enough so that the end of the cutter enters the coil by about a 1/4" make sure the cutter is level with the book before you cut. As you squeeze the cutters you may notice the coil wants to twist. You can support the coil with your f...
Page 13: Wire Closer Module
Wire closer module 2) installation instructions: diagram 3 procedure to attach the wire closer onto the combo binding station or the od 4000 punch. Place the closer module on the backside of the combo binding station or the od 4000 punch so the closer adjustment knobs are facing the front of the com...
Page 14: (120
Coil inserter module electrical schematic (120 volt ac) power entry module note: the motor is protected by a thermal overload located in the motor. It will reset automatically after the motor cools. This product has earned the ul listing mark and the ul listing mark for canada. El 79574 the cl 3000 ...
Page 15: Wire Closer Module
Wire closer module 2) installation instructions: diagram 3 procedure to attach the wire closer onto the combo binding station or the od 4000 punch. Place the closer module on the backside of the combo binding station or the od 4000 punch so the closer adjustment knobs are facing the front of the com...
Page 16
Setup instructions: diagram 4a, 4b, 4c & 4d a) determine the correct wire size. Use the table below to determine the correct wire size for the book thickness. You can insert more sheets into the wire, but it may affect the appearance of your book. Covers are not included with the number of sheets co...
Page 17
C) setting the closing bar height the closing bar is adjustable on each end allowing the operator to achieve a perfect close at each end of the book. Pull the handle on the closer all the way down and adjust both knobs (3) so the top edge (4) of the closing bar lines up with the line (5) next to the...
Page 18
Diagram 4c diagram 4d 1-800-543-5454 www.Officezone.Com officezone.
Page 19: Comb Opener Module
Comb opener module 3) installation instructions: diagram 5 procedure for attaching the comb opener onto the combo binding station or od 4000 punch. Place the comb opener module on the backside of the combo binding station or od 4000 punch so the narrow section of the comb opener is facing the front....
Page 20
A) determine the correct comb size. Use the table below to determine the correct comb size for the book thickness. You can insert more sheets into the comb, but it may affect the appearance of your book. Covers are not included with the number of sheets column. Comb diameter inch 3/16 book thickness...