1. DL manuals
  2. Oki
  3. All in One Printer
  4. ES 1624n MFP
  5. Setup And Installation Manual

Oki ES 1624n MFP Setup And Installation Manual

Manual is about: Oki Printer Users' Guide

Summary of ES 1624n MFP

  • Page 3

    3 es1624 mfp setup and installation guide installation overview notes, cautions, and warnings ................4 select location ........................................4 checking package contents .....................4 scanning unit......................................... 4 printing unit..............

  • Page 4

    4 notes, cautions, and warnings only use genuine oki original consumables to ensure the best quality and performance from your hardware. Non-oki original products may damage your printing unit’s performance and invalidate your warranty. Specifications subject to change without notice. All trademarks...

  • Page 5

    5 setting up the printing unit 1. Remove the transport tape from front and back of printing unit. Install the support bracket 2. Place the printing unit on the surface you have chosen. Place the support bracket ( 1 ) at the back of the printing unit. 3. Carefully lift the back of the printing unit a...

  • Page 6

    6 attaching the scanning unit 1. Before attaching the scanning unit you must remove the two transport restraints ( 1 ) located on mounting posts on the printing unit. A.First, turn the locking knob on the side of the printing unit to the unlock position. This will release the transport restraint. B....

  • Page 7

    7 connecting the cables connect the adf cable connect the adf cable (attached to the documents cover), to the adf port on the scan unit. Connect the ethernet cable connect one end of your ethernet lan cable to an available port of your ethernet hub. Connect the other end to the lan port at the back ...

  • Page 8

    8 connect the power connector cord 1. Connect the power connector cord to the power adapter on the scanning unit. 2. Connect the other end to the printer unit power input port. Attach the ac power cord. 3. Be sure the printing unit power switch is in the "0" position. Connect the ac power cord to a ...

  • Page 9

    9 preparing the image drum/ toner cartridges 1. Press the cover release button and lift the top cover. 2. Carefully lift the black toner/drum cartridge out of the printing unit. 3. Unwrap the protective sheet and place the cartridge on a flat work surface. 4. Pull out both the protective sheet and t...

  • Page 10

    10 7. Repeat steps 2 to 6 with remaining toner/ drum cartridges. Preparing the fuser 1. Observe the instructions printed on the orange band. 2. Remove the orange band. Press firmly on the blue lock (1) to release the orange transport restraint (2). Pull the restraint out in the direction of the arro...

  • Page 11

    11 loading paper 1. Pull out the paper tray. 2. Remove the transport restraint by pulling downward then out. 3. Adjust the rear ( 1 ) stopper and paper guides ( 2 ) to the size of paper being used. Do not overload. 4. Load the paper. 5. Close the paper tray..

  • Page 12

    12 turning power on turn printing unit power on turn power switch to the " ❘ " position. Turn scanning unit power on wait until the power (ready) led illuminates solid green on the printing unit status panel. Turn scanning unit power to the " ❘ " position. Important note! Do not turn the scanning un...

  • Page 13

    13 network installation: windows ® minimum configuration requirements to make the best of this mfp, the following configuration is required: to send e-mails: • tcp/ip network. • a smtp and a optional pop3 server. To file document(s) via intranet: • ftp, http, or cifs protocol environment. • windows ...

  • Page 14

    14 installing drivers and network software 1. Check to be sure the usb cable is not connected to your computer. 2. Insert cd1 into your cd-rom drive. The cd will autorun. If it doesn’t, click start → run → browse . Browse to your cd-rom drive. Double-click install.Exe . Click ok . 3. Select your lan...

  • Page 15

    15 configuring your mfp this section is specifically for persons who are responsible for the administration of this mfp. There are three methods to configure your machine. • from the oki mfp network setup tool • from the mfp’s web page • from the control panel configuring from the oki management uti...

  • Page 16

    16 additional network software the following additional network utilities can be installed by clicking on the network software button: web driver installer utility use this utility to create a web page and set up your mfp with groups of clients who have access. Once the unit has been registered by t...

  • Page 17

    17 operating your mfp for more information on operating your machine, see the on-line users guide located on the supplied cd. Placing document(s) in the adf 1. Make sure your document is free of staples, paper clips and is not torn. 2. If your have multiple pages, fan your documents to avoid occasio...

  • Page 18

    18 quick operation press copy mode key. Enter your copy count via the numeric keypad. Press to make b&w copy. Press to make color copy. Press scan to mode key. Choose your e-mail address from the address book. I.E. + + press to send your document in b&w. Press to send your document in color. Press s...

  • Page 19

    19 for additional information for additional information about your mfp, see these sources: • the electronic user’s guide’s on the supplied cd for expanded information on using your mfp. • the handy reference guide. • the help files available with the utility programs. For assistance if you need fur...

  • Page 20

    Oki data americas, inc., 2000 bishops gate blvd., mt. Laurel, nj 08054-4620 tel: (856) 235-2600 fax: (856) 222-5320 http://my.Okidata.Com oki data americas, inc., 2735 matheson blvd. East, unit 1, mississauga, ontario l4w 4m8, canada télép: 1-800-654-3282 téléc: 1-905-238-4421 http://my.Okidata.Com ...