DL manuals
Oki
Printer Accessories
T400
Installation Manual

Oki T400 Installation Manual

Other manuals for T400: Safety Information Manual, Install Sheet, Setup Manual, User Manual, Installation

Manual is about: T400/T410 User Guide

Page of 12

Download

Print this page

Bookmark us

Page 1

DISPENSER KIT COMPONENTS

(USED ON DIRECT THERMAL AND

THERMAL TRANSFER UNITS)

STEP

PROCEDURE

Switch the printer OFF and disconnect the power cord.

Raise the top cover and print head assembly.

Remove the front door panel.

Raise the tear bar to the upright position to unlock the Platen Roller

Assembly.

Refer to the illustrations on the following pages.

Gently lift the right side of the platen from the support yoke, then

maneuver the geared left side to free from the opposite support yoke.

Note the position of the components. The new Dispenser Plate will

replace the existing Tear Bar on the Platen Roller Assembly.

Detach "C" rings from both ends of the platen and slide off the gear and

bearings. Remove the existing tear bar.

Install the dispenser plate in the same location as was the tear bar.

Replace bearings and gear and reattach "C" rings.

Install the altered platen assembly back into the printer.

TEXT CONTINUED ON PAGE 4

DISPENSER

KIT

DISPENSER

PLATE

GUIDE SHEET

Direct Thermal Unit: For Thermal Transfer Unit see page 6

Installing the Dispenser Kit

1 2 3 4 5 6 7 Next › »

Summary of T400

Page 1
Page 1 dispenser kit components (used on direct thermal and thermal transfer units) step procedure 1. Switch the printer off and disconnect the power cord. 2. Raise the top cover and print head assembly. 3. Remove the front door panel. 4. Raise the tear bar to the upright position to unlock the plat...
Page 2: Installing The Dispenser Kit
Page 2 installing the dispenser kit left end of platen in support yoke right end of platen in support yoke gently lift platen from the right side of the support frame and gears on the left direct thermal unit.
Page 3: Installing The Dispenser Kit
Page 3 installing the dispenser kit remove bearings, gear and "c" rings install dispenser plate and replace bearings, gear and "c" rings install dispenser plate after removing existing tear bar remove "c" rings both ends direct thermal unit.
Page 4: Installing The Dispenser Kit
Page 4 installing the dispenser kit line up edge of guide sheet and notch press down to attach to front door panel peel backing paper from guide sheet step procedure 9. Remove the backing paper from the guide sheet. Line up one side of the guide sheet (match notch on guide sheet with notch on front ...
Page 5: Installing The Dispenser Kit
Page 5 installing the dispenser kit plug connector into cn13 right side locating pin secure dispenser with (2) screws line up holes with locating pins direct thermal unit.
Page 6: Installing The Dispenser Kit
Page 6 installing the dispenser kit step procedure the ribbon assembly on the thermal transfer unit has a gear that meshes with the gear on the platen roller assembly and must be disengaged to allow the platen roller assembly to be removed. 1. Switch the printer off and disconnect the power cord. 2....
Page 7: Installing The Dispenser Kit
Page 7 installing the dispenser kit thermal transfer unit: remove screw to detach lever from print head and ribbon assembly insert a flat blade screwdriver under this bracket (or by other means) to disengage this end of the ribbon assembly from the print head positioning pin on backside of bracket f...
Page 8: Installing The Dispenser Kit
Page 8 installing the dispenser kit for thermal transfer unit: slide the ribbon assembly backward to disengage this end from the print head positioning pin on the underside of the ribbon assembly fits into hole on print head reconnect if disengaged.
Page 9: Installing The Dispenser Kit
Page 9 left end of platen in support yoke right end of platen in support yoke gently lift platen from the right side of the support frame and gears on the left installing the dispenser kit for thermal transfer unit:.
Page 10: Installing The Dispenser Kit
Page 10 remove bearings, gear and "c" rings install dispenser plate and replace bearings, gear and "c" rings install dispenser plate after removing existing tear bar remove "c" rings both ends installing the dispenser kit for thermal transfer unit:.
Page 11: Installing The Dispenser Kit
Page 11 installing the dispenser kit for thermal transfer unit: plug connector into cn13 right side locating pin secure dispenser with (2) screws line up holes with locating pins.
Page 12: Installing The Dispenser Kit
Page 12 step procedure 12. Remove the backing paper from the guide sheet. Line up one side of the guide sheet (match notch on guide sheet with notch on front door panel). Press down firmly to attach. 13. Attach connector from the dispenser kit to cn13 on the printer as shown. 14. Position the dispen...