PACH & COMPANY AeGIS 7000 Series Installation And Programming Manual - page 29
AeGIS 7000 SERIES QUICK REFERENCE GUIDE
1) PRESS 0 AND # SIMULTANEOUSLY THEN RELEASE
, the display screen stops scrolling (If the display screen is still scrolling repeat this step again) then
enter the valid 4-digit Master Code (default Master Code: 0000). Now, you are in programming mode and see table below to continue.
2) IF YOU DO NOT HAVE A VALID MASTER CODE
, open the panel (key must be used) then press and release the “RED BUTTON” on the board and the
display shows:
x x x x: 4-digit Master Code, then press #. Now, you are in programming mode and see table below to continue.
1) SINGLE SYSTEM
Step 1 Call the AeGIS 7000. When the system answer you will hear: • One Short Beep: Door is opened; • Two Short Beeps: Door is closed.
Then Press # key
Step 2 Press your valid Master Code.
• If your Master Code is accepted, you will hear Two Short Beeps and now, you are in the programming mode and see table below to continue
• If your Master Code is rejected, the system will disconnect.
2) MULTI-SYSTEM IN SINGLE TELEPHONE LINE
Step 1 Call into the AeGIS 7000 using a touch tone phone. When the system answer
you will hear: • One Short Beep: Door is opened; • Two Short Beeps: Door is closed; • One Long Beep: Combination of Closed and open.
Step 2 Press the System Number you want to log in (1-8) then press # key.
Step 3 Press your valid Master Code.
• If your Master Code is accepted, you will hear Two Short Beeps and you are in the
programming mode and see table below to continue.
• If your Master Code is rejected, the system will disconnect.
Step 4 Follow the next programming sections below to program the tenant database and parameter.
LOCAL PROGRAMMING
REMOTE TOUCH-TONE PROGRAMMING
SYSTEM’S OPERATION
KEYPAD LAYOUT
TO PLACE A CALL FROM THE AeGIS 7000 SERIES: • Press 3 to scroll the tenant name from
A to Z. o r Press 6 to scroll the tenant name from Z to A, then press #.
TO PLACE A DIRECT CALL: Press # , wait for a dial tone then press the 2, 3 or 4 digit directory
number.
TO GRANT ACCESS TO VISITOR : Press 9
TO DISABLE REMOTE ACCESS: See Function Code 77.
TO USE THE 4-DIGIT ACCESS CODE: Press * then the 4-digit code.
TO EXTEND THE TALK TIME: Tenant must press the # after the time-out warning beep, the talk
time will be extended to another cycle.
TO CALL INTO THE AeGIS 7000 SERIES: Dial the AeGIS phone number, you hear “ONE
SHORT BEEP” if you are connected then press * to communicate with the visitor and press 9 to
unlock the door.
See manual for
more detail
FUNCTION CODE TABLE
CODE
DESCRIPTION
CODE
DESCRIPTION
*
#
00
01
02
03
04
05
06
07
08
10
Exit the programming (local programming) or clear
the existing field
To accept program.
Replace System Master Code.
Program a New Tenant.
Modify an Existing Tenant Directory.
Delete an Existing Tenant Directory.
Clear All Tenants Directory.
Manual Lock (open) or Unlock (close) Door.
Selecting Directory Digits (2, 3, or 4-digit, default is
3-digit).
Single or Multi Systems (default is single).
System Number (default is 1).
Edit Welcome Screen.
46
50
70
71
72
73
74
75
76
77
78
91
System Information.
Clear the Memory to Factory default.
Change Talk Time (default is 60 seconds).
Change Door Open Interval (default is 12 sec).
Change Lock Out Count (default is 3 times).
Select Tone and Pulse Dialing (default is tone).
Enable or DIsable Auto Answer (default is enabled)
Turn On or Off Key Press Beep (default is On).
Turn On or Off Speaker Beep. (default is On).
Enable or Disable Remote Access (default is
enabled).
View Directory by Name.
Exit from Remote Programming.