091013-20 summit-b 5055.3252 installation and operating instructions safety notice if this stove is not properly installed, a house fi re may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection require...
2 summit-b 091013-20 contents safety and maintenance .............................................................. 3 maintenance checks ................................................................... 4 creosote .......................................................................................
Summit-b 091013-20 3 safety and maintenance 1. Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood should not be used, as it will reduce heat output, as well as contributing signi...
4 summit-b 091013-20 maintenance checks check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (see website for descriptions and more detail) weekly: - firebrick - visual, for cracking. - door gasket - sagging, placement, damage. Monthly ...
Summit-b 091013-20 5 creosote formation and need for removal when wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney fl ue of a slow burning fi re. As a result, creosote...
6 summit-b 091013-20 double wall connector - residential double wall connector - mobile home single wall connector - residential fig. #2 minimum clearance to combustibles alcove: min. Height 7' max. Depth 4' optional ash cleanout system 1) remove nuts holding the ash system hole cover and gasket loc...
Summit-b 091013-20 7 procedure: caution: the structural integrity of the mobile home floor, wall and ceiling/roof must be maintained. The space heater is to be connected to a factory- built chimney conforming to can/ulc-s629 standard for 650c factory-built chimneys. Note: see "combustion air" sectio...
8 summit-b 091013-20 fig. #3 chimney roof fl ashing storm collar * 4" diameter air inlet with rodent screen * if the crawl space is well ventilated it is not necessary to extend air inlet to outside spark arres- tor rain cap radiation shield chimney connector chimney support 54" (1372 mm) minimum mi...
Summit-b 091013-20 9 residential installation warning: under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It may be fi red only after the following conditions have been met. * do not attempt to connect this heater to any air distribution duct. * outside combu...
10 summit-b 091013-20 canada only floor protector the stove may be installed on a combustible fl oor provided noncombustible ember protection is used. This protection must extend as follows: in canada: 18" (457 mm) on the fi ring side and 8" (203 mm) to the other sides. See figure #4, below. Combust...
Summit-b 091013-20 11 operation caution: never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fl uid or similar liquids to start or "freshen up" a fi re in this heater. Keep all such liquids well away from the heater while it is in use. Caution: hot while in operation. Keep chi...
12 summit-b 091013-20 baffle removal chimney connector pipe should be disconnected from stove to clean and inspect. Only if this is not possible should you remove baffle assembly. Do not operate with baffle assembly or insulation removed. Removal remove retaining pin at the rear inside top of the fi...
Summit-b 091013-20 13 troubleshooting problem cause cure glass is dirty 1. Wood is wet - use dry wood 2. Turning down air control - do not turn down until or damper too soon a) there is a good bed of coals b) the wood is charred 3. Draft too low - improper chimney height and / or diameter - chimney ...
14 summit-b 091013-20 operating tips 1. Always use dry, seasoned fi rewood, up to 18" long. Load wood endwise, a mixture of large and small pieces, on top of a good ash base (1" minimum). 2. Operate on a medium to high setting, for up to 1 hour from cold start. After the initial warm up pe- riod, re...
Summit-b 091013-20 15 replacement parts item description part no. Item description part no. 1............ Side shield, left or right...................... Summ.3201 2............ Rear defl ector ......................................Summ.3203 3............ Cast ash lip .................................
16 summit-b 091013-20 replacement parts - summit classic item description part no. Item description part no. 1............ Top panel .......................................Suca.3251xxa 2............ Screen trivet ..................................... Clad.Ctxxa 3............ Side shield ...............
Summit-b 091013-20 17 super 27 and pacifi c summit note: optional ash dump kit should be installed prior to pedestal or leg kit assembly. Required: pedestal kit leg adapter 1 pedestal base 1 ash drawer enclosure 1 front cover (attached) 1 front cover (attached) 4 1/2" washers with leg set 4 legs cra...
18 summit-b 091013-20 item size part number a 1 1/2” x 4 1/2” x 1 1/4” (39 mm x 115 mm x 32 mm) 248.001 b 4” x 4 1/2” x 1 1/4” (102 mm x 115 mm x 32 mm) 246.001 c 7 1/4” x 4 1/2” x 1 1/4” (184 mm x 115 mm x 32 mm) 245.001 d 9” x 4 1/2” x 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 e 9” x 4 1/2” (cut) x...
Summit-b 091013-20 19 label a. 14 in. / 356 mm 14 in. / 356 mm b. 9 in. / 229 mm 9 in. / 229 mm c. 6 in. / 152 mm 6 in. / 152 mm summit d. 23.8 in. / 605 mm 23.8 in. / 605 mm e. *14.5 in. /368 mm *14.5 in. /368 mm f. *17.3 in. / 439 mm *17.3 in. /439 mm alderlea t6 d. 25.6 in. / 650 mm 25.6 in. / 65...
Pacific energy fireplace products ltd. 2975 allenby rd., duncan, b.C. V9l 6v8 phone: 250-748-1184 web site: http://www.Pacifi cenergy.Net printed in canada.
