1. DL manuals
  2. PNI
  3. Nail Gun
  4. PORTAMATIC 475 Twin Trigger 20
  5. Owner's Manual

PNI PORTAMATIC 475 Twin Trigger 20 Owner's Manual

Manual is about: Thin Flooring Stapler For 1/4” - 7/16” Tongue and Groove Engineered and Solid Wood Flooring

Summary of PORTAMATIC 475 Twin Trigger 20

  • Page 1

    “pni is a proud member of these industry associati ons” po box 1257, wilmington, nc 28402 910-283-9791 • 800-634-9281 • fax 910-283-6264 home page: www.Porta-nails.Com e-mail: info@porta-nails.Com owner’s manual portamatic® 475 twin trigger 20 thin flooring stapler for 1/4” - 7/16” tongue and groove...

  • Page 2

    2 introduction the portamati c 475 fl ooring stapler is a precision-built tool, designed for high speed, high volume fastening. This tool will deliver effi cient, dependable service when used correctly and with care. As with any fi ne power tool, for best performance the manufacturer’s instructi ons m...

  • Page 3

    18 475 part number descripti on 66 47566 plate (10066) 67 47567 secondary trigger (10067) 68 47568 cap, trigger cable (10068) 69 47569 trigger cable (10069) 70 47570 magazine core (10070) 71 47571 pusher (10071) 72 47572 magazine, slide (10072) 73 47573 spring pin (10073) 74 47574 spring pin (10074)...

  • Page 4

    4 safety instructions tool operati on the employer is responsible for ensuring that the manufacturer’s tool operati ng/safety instructi ons are available to operators. The employer and the tool operator are responsible for the safe use of the tool. The employer and tool operator are responsible for ...

  • Page 5

    16 475 flooring stapler - part listing 475 part number descripti on 1, 1a 47501 screw, shcs (10001) 2 47502 cap (10002) 3 47503 gasket, cap (10003) 4 47504 top seal (10004) 5 47505 poppet (10005) 6 47506 o-ring (10006) 7 47507 o-ring (10007) 8 47508 spring, head valve (10008) 9 47509 head valve (100...

  • Page 6

    6 determine that the tool is in proper working order. • an improperly functi oning tool must not be used. Tool handling always assume that the tool contains fasteners. • do not point the tool toward yourself or anyone whether it • contains fasteners or not. Do not actuate the tool unless the tool is...

  • Page 7

    14 maintaining the pneumatic tool when working on air tools, note the warnings in this manual and use extra care evaluati ng problem tools. Caution: pusher spring (constant force spring). Cauti on must be used when working with the spring assembly. The spring is wrapped around, but not att ached to,...

  • Page 8

    8 air supply hoses shall have a minimum working pressure rati ng equal to or greater than the pressure from the power source if a regulator fails, or 150 psig, whichever is greater. Disconnect tools shall be fi tt ed with a fi tti ng or hose coupling on or near the tool in such a manner that all com...

  • Page 9

    12 sequential trip safety operation the model 475 fl ooring stapler operates on a sequenti al trip system. The sequenti al trip system requires the operator to hold the tool against the work before pulling the trigger. This makes accurate fastener placement easier. The sequenti al trip allows exact ...

  • Page 10

    10 air supply and connections warning: ! Do not use oxygen, combusti ble gases, or bott led gases as a power source for this tool as tool may explode, possibly causing injury. Fittings: install a male plug on the tool which is free fl owing and which will release air pressure from the tool when disc...