Q-See QH8013Z User Manual - page 8
14
15
Date Setup, Title Setup - These will appear on screen (and be recorded by the DVR as part of
the video) only if enabled in the
Display Setup option. Your DVR also has the ability to include this
information. If you choose to utilize these, use the directional arrows to navigate through the entries.
When complete, select Preset 001 from the pull down and click
to save it. Or, select Preset
002 and click
to exit out of the menu without saving changes.
North Setup - You can choose a point that the camera will regard as “North”. If enabled in the
Display Setup option, the camera will display its position in degrees from its “North”. In addition to
the horizontal position, the camera will consider 0° (horizontal) as part of the setting and will show
the vertical depression from that point as well.
Home Position - You can cause your camera to return to a specific “Home” position after a set
period of time (5 seconds to 3 minutes). By using this setting, you can have the camera monitor a
specific point until and alarm (set up in the DVR) triggers an action, such as a cruise. Afterwards, it
will return back to its starting point.
The date, time, and position displays will only appear on screen if enabled in the
Display Setup
menu (page 20).
The QH8013Z’s internal menu provides another method to control its movements as well as allow-
ing the user to make settings to the camera itself. These settings range from changing the camera’s
address and baud rate to adjusting the color balance, day/night mode and zoom speed.
CAMERA MENU
MAIN MENU
1 SYSTEM INFORMATION
2 SYSTEM SETUP
3 CAMERA SETUP
4 PRESET SETUP
5 DOME FUNCTION
6 DISPLAY SETUP
7 LOAD DEFAULT
0 EXIT
SYSTEM INFORMATION
1 VERSION:
V1.10
2 CAMERA:
HD20T
3 TEMPERATURE: 72°F
4 DATE:
01-24-14
5 DOME ID:
001
6 PROTOCOL:
PELCO-P
7 BAUD RATE: 9600
0 RETURN
In your DVR’s
PTZ Controls, select Preset
95 in the pull-down and click
to enter the
camera’s internal menu.
MENU NAVIGATION
Use the PTZ “up” and “down” directional arrows
to move around in the menu.
Click on the right arrow to:
∙ Select an option from a menu.
∙ Enter a submenu designated by “ ”
∙ To confirm a setting (i.e., clicking Enter)
The left arrow is used to go back to the menu
item.
Start Track
Start Track
Start Auto Scan
Start Auto Scan
Start Cruise
Start Cruise
Preset
Cruise
Preset
Cruise
Speed: 5
Speed: 5
preset 101
preset 101
02
02
01
01
03
03
04
04
05
05
06
06
07
07
08
08
All
All
Zoom
Focus
Iris
Zoom
Focus
Iris
Move Up
Move Right/
“Enter”
Move
Left
Move Down
To go up one level (i.e.; back to the Main menu
from a submenu), click on Return.
To go up one level (i.e.; back to the Main menu
from a submenu), click on 0 Return.
SYSTEM INFORMATION WINDOW
This window shows the current settings for the
camera. The menu cannot be navigated.
SYSTEM SETUP
1 AUTO PT FLIP: ON
2 LANGUAGE SETUP
3 RS422 SETUP
4 DATE SETUP
5 TITLE SETUP
6 NORTH SETUP
7 HOME POSITION
0 EXIT
RS422 SETUP
1 RS422/ID SEL:S/W
2 DOME ID:
001
3 PROTOCOL:
PELCO-P
4 BAUD RATE: 9600
0 EXIT
SYSTEM SETUP WINDOW
As the name says, this is where you will make your
changes to the camera’s general settings.
Auto PT Flip - When this is enabled, and the
camera is programmed to go beyond 90° (straight
down), the camera will quickly rotate so that the
lens will be able to continue to elevate with the
image right side up.
Language Setup - English is the only available
option.
RS422 Setup - Change your camera’s address,
baud rate and communication protocol.
Leave “RS422/ID SEL” set to S/W (software).
If you change any of the other settings in this
window, you will have to change the settings in
the DVR to match.
Dome ID - This is the camera’s address. It can
range from 1-255.