Summary of DM-X10
Page 1
Dm-x10 192 channel dmx controller user manual 154.091uk vers ion 1.0
Page 2: Content
U s e r m a n u a l 1 content 1. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 1 . 1 1.2 before you begin what is included.................................. Unpacking instructions safety instructions ..................................................................
Page 3
1.1 what is included 1) dm-x10 controller 2) dc 9-12v 500ma, 90v~240v power adapter 3) manual 1.2 unpacking instructions immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the sh...
Page 4: Ntroduction
2. I ntroduction 2.1 features * universal dmx-512 controller * controls 12 intelligent lights of up to 16 channels * 30 banks of 8 scenes, 240 scenes total * 6 sets of chases containing 240 scenes * execute multiple chases simultaneously * beat-activation, tap sync, auto run * polarity selector 2.2 ...
Page 5
Item button or fader function selected 4 dmx 512 cont r olle r s e r ie s u s e r m a n u a l fixture select buttons fixture selection fixture indicator leds indicates the fixtures currently universal bump buttons representing scene selection scene select buttons location for storage and channel fad...
Page 6: 3.Operating Instructions
2.5 common terms the following are common terms used in intelligent light programming. Blackout is a state by where all lighting fixtures light output are set to 0 or off, usually on a temporary basis. Dmx-512 is an industry standard digital communication protocol used in entertainment lighting equi...
Page 7: 113
3.1.2 fixture addressing the dm-x10 is programmed to control 16 channels of dmx per fixture, therefore the fixtures you wish to control with the corresponding fixture buttons on the unit, must be spaced 16 channels apart. Fixture or scanner # default dmx starting address binary dipswitch settings sw...
Page 8
3.1.3 fade time assign you can choose whether the board s fade time during scene execution is implemented broadly to all output channels or only to the pan & tilt movement channels. This is relevant because often you will want gobos and colors to change quickly while not affecting the movement of th...
Page 9
Action : ( scene review) 2) select a scene button (1~8) to review. 1) select any one of the 30 banks by pressing the bank up/down buttons. 3) move faders to change fixture attributes. Notes : make sure you are still in manual mode. 3.3 programming a program (bank) is a sequence of different scenes (...
Page 10
Action : 2) press the auto del button repeatedly until the auto led turns on. 1) use bank up/down buttons to change program banks if necessary. 3) adjust the program speed via the speed fader and the loop rate via the fade time fader. Notes : deselect blackout if led is lit. 3.3.3 running a program ...
Page 11
3.4 chase programming action : 2) adjust the chase speed by tapping the tap display button twice at a rate of your choosing. 1) press a chase button then press the auto del button. Notes : the time between 2 taps will set the chase speed (up to 10 minutes) 3.4.1 create a chase action : 2) press the ...
Page 12
3.4.5 edit chase (copy scene into chase) action : 2) press the desired chase button. 1) press and hold the program button to enter programming mode. Notes : i .E. To insert a scene between steps 05 and 06 navigate using bank buttons until the display reads step05. Action : 2) press the desired chase...
Page 13
3.4.9 delete all chase programs action : 2) press the desired chase button. 1) press and hold the program button to enter programming mode. Notes : i .E. To insert a scene between steps 05 and 06 navigate using bank buttons until the display reads step05. Action : 2) press and hold the bank down but...
Page 14
3.5.3 delete a scene action : 2) turn the controller back on. 1) press and hold the program button and the bank down button while turning off power to the controller. Notes : caution! This process is irreversible. All scenes with data will be set to 0. Action : 2) select the bank that contains the s...
Page 15: 4 Appendix
4 appendix 4.1 dmx primer there are 512 channels in a dmx-512 connection. Channels may be assigned in any manner. A fixture capable of receiving dmx 512 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserv...
Page 16
4.3 dmx dipswitch quick reference chart dmx address quick reference chart #1 #2 #3 #4 #5 #6 #7 #8 #9 0 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 42 43 44 45 46 47 48 41 40 39 38 37 36 35 34 33 32 95 94 93 92...
Page 17
4.4 technical specifications weight........................................................................................................................... 3.5 kg operating range.....................................................................................Dc 9v-12v 500ma min maximum ambien...