Quality Craft MM650C-38ACH Instruction Manual

Page of 8

Download

Print this page

Bookmark us

ELECTRIC FIREPLACE

HEATER

Model: MM650C-38ACH

IMPORTANT:

PLEASE NOTE: WHEN YOU OPEN THE CARTON, CAREFULLY CHECK THE UNIT AND

MAKE SURE THERE IS NO DAMAGE. IF YOU HAVE ANY PROBLEMS WITH THE UNIT,

WITH HOW THE VARIOUS FUNCTIONS WORK, OR HAVE DAMAGED OR MISSING

PARTS PLEASE CALL 1-800-459-4409 (MONDAY TO FRIDAY, 8:30AM TO 5:00PM,

EST) IMMEDIATELY FOR SERVICE.

NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE

NUMBER. DO NOT DISPOSE OF YOUR CARTON UNTIL YOU ARE COMPLETELY

SATISFIED WITH YOUR NEW FIREPLACE HEATER.

NOTE: Light bulbs may become loose during shipping. If the fl ame effect is dim or does

not work, please check that light bulb or bulbs are fi nger tight in socket. See instructions for

replacing bulb or bulbs.

NOTE: The electric fi replace heater may emit a slight harmless odor when fi rst turned on.

This is caused by activating the internal heater components for the fi rst time and should not

occur again.

INSTRUCTION MANUAL

ATTENTION:

1. Find a location for the fi replace heater that is protected from direct sunlight.

2. Do not plug the unit into the power outlet before reading all instructions.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS

BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO

PERSONS, INCLUDING THE FOLLOWING:

1) Read all instructions before using this electric ﬁ replace heater.

2) This electric ﬁ replace heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces. The grill directly in front of the heater outlet becomes

hot during heater operation. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away

from the front of the unit and keep them away from the sides and rear.

3) Extreme caution is necessary when any heater is used by or near children

or individuals with disabilities and whenever the ﬁ replace is left operating

and unattended.

4) Always unplug ﬁ replace when not in use.

5) Do not operate any electric ﬁ replace with a damaged cord or plug or after

the heater malfunctions, has been dropped or damaged in any manner.

6) Do not use outdoors.

7) This electric ﬁ replace heater is not intended for use in bathrooms, laundry

areas and similar indoor locations. Never locate heater where it may fall into a

bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or

similar coverings. Arrange cord away from trafﬁ c area and where it will not be

tripped over.

9) To disconnect ﬁ replace, turn controls to off, then remove plug from outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or ﬁ re, or damage the heater.

12) To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner.

Do not use on soft surfaces, like a bed, where openings may become blocked.

13) A heater has hot and arcing or sparking parts inside. Do not use it in areas

where gasoline, paint, or ﬂ ammable liquids are used or stored.

14) Use this ﬁ replace heater only as described in this manual. Any other use not

recommended by the manufacturer may cause ﬁ re, electric shock, or injury

to persons.

15) Avoid the use of an extension cord because the extension cord may overheat

and cause a risk of ﬁ re. However, if you have to use an extension cord, the cord

shall be No.14 AWG minimum size and rated not less than 1875 watts.

16) Do not plug this product into a receptacle controlled by a wall switch

or dimmer.

17) When storing or transporting the unit and cord, keep in a dry place,

free from excessive vibration and store so as to avoid damage.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE.

CAUTION:

IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL CONTROL, A

PROGRAM CONTROLLER, A TIMER OR ANY OTHER DEVICE THAT SWITCHES THE

HEATER ON AUTOMATICALLY, REMEMBER TO OBSERVE ALL SAFETY WARNINGS

AT ALL TIMES. THE FIREPLACE HEATER HAS SAFETY OVERHEAT PROTECTION.

IF THE OVERHEAT PROTECTION TRIPS, SWITCH OFF ALL SWITCHES AND WAIT

APPROXIMATELY 5–10 MINUTES. IT SHOULD RESET AUTOMATICALLY ONCE THE

UNIT COOLS DOWN.

WARNING:

PROCEDURES AND TECHNIQUES, IF NOT CAREFULLY FOLLOWED, WILL RESULT

IN DAMAGE TO THE EQUIPMENT, AND WILL EXPOSE THE USER TO THE RISK OF

SERIOUS INJURY, ILLNESS OR DEATH.

THIS ELECTRIC FIREPLACE HEATER IS FOR USE ON 120 VOLTS. THE CORD HAS

A PLUG AS SHOWN AT A IN ILLUSTRATION BELOW. AN ADAPTER AS SHOWN AT

C IS AVAILABLE FOR CONNECTING THREE-BLADE GROUNDING-TYPE PLUGS TO

TWO-SLOT RECEPTACLES. THE GREEN GROUNDING PLUG EXTENDING FROM

THE ADAPTER MUST BE CONNECTED TO A PERMANENT GROUND SUCH AS A

PROPERLY GROUNDED OUTLET BOX. THE ADAPTER SHOULD NOT BE USED IF A

THREE-SLOT GROUNDED RECEPTACLE IS AVAILABLE.

A 15 AMP CIRCUIT IS REQUIRED TO OPERATE THIS HEATER. IF THE BREAKER

TRIPS WHEN THE HEATER IS USED, YOU MAY NEED TO MOVE THE HEATER TO

ANOTHER LOCATION OR UNPLUG OTHER APPLIANCES THAT ARE ON THE SAME

CIRCUIT. IF YOU REQUIRE AN EXTENSION CORD, USE ONE THAT IS RATED AT

1875 WATTS.

MM650C-38ACH_qualitycraft_walmart_com_fireplace-manual_2.indd 1

12-12-10 9:39 AM

1 2 3 4 5 6 7 Next › »

Summary of MM650C-38ACH

Page 1
1 electric fireplace heater model: mm650c-38ach important: please note: when you open the carton, carefully check the unit and make sure there is no damage. If you have any problems with the unit, with how the various functions work, or have damaged or missing parts please call 1-800-459-4409 (monda...
Page 2
2 back parts list: fireplace insert...................................................................................................... 1 a) top panel ........................................................................................................ 1 b) base panel .............................
Page 3
3 step 1: attach all plastic connector [t] to the panels [c, h, j, k and l] as shown in fig. A (2 pcs kd screws for each connector). Fig. A back step 2: attach the left small panel [h] to the left front panel [f] with 2 kd screws. Attach the right small panel [j] to the right front panel [g] with 2 ...
Page 4
4 step 5: place the lower front panel [e] in between the lower sections of left and right small panel [h and j] and attach with 2 kd screws (1 screw each side). See fig. E. Fig. E back step 6: place the upper front panel [d] in between the upper section of left and right front panels [f and g] and a...
Page 5
5 step 9: attach the corner piece [m] on the top panel [a] and attach with 6 small screws [s]. See fig. I. Fig. I back step 10: install the top panel [a] to the unit with 4 kd screws. See fig. J. Fig. J back step 11: tighten all screws. Fig. K. Fig. K back fireplace insert installation: the fireplac...
Page 6
6 fig. N back 4. Use the screw for wall to attach the other end of safety cable to the wall. 5. Make sure all screws are tight. Operation after reading complete instructions, confirm all controls on fireplace are in the off position. Plug the fireplace into a 15amp/120volt outlet. If the cord does n...
Page 7
7 touch-up repair paint paint directly on the mantel unit if necessary. Repairs if any problems are found with the original parts during mantel assembly – such as if the panels cannot be installed with the plastic connector – try to solve by one of the following methods. Tools required: electric dri...
Page 8
8 warranty every electric fireplace heater is tested before it leaves the factory and it is guaranteed for one year. If the unit should fail to operate correctly within one year from the date of purchase, call customer service at 1-800-459-4409 (monday to friday, 8:30am to 5:00pm, est). We will, at ...