1. DL manuals
  2. Quantum
  3. Storage
  4. FastStor 1
  5. Install Manual

Quantum FastStor 1 Install Manual

Manual is about: Quantum FastStor 1: User Guide

Summary of FastStor 1

  • Page 1

    Faststor rack mount installation instructions.

  • Page 2: Precautions

    Ii faststor rack mount installation instructions 62-0125-01 precautions you must consider the following precautions when installing a faststor unit in a rack system: 1. Maximum recommended ambient temperature is 40º c. Internal temperature of rack should be considered for continued safe operation. 2...

  • Page 3

    62-0125-01 faststor rack mount installation instructions 1 rack mounting a single faststor these instructions provide detailed descriptions of the steps you must perform to install a single faststor in a single slot of your rack. You’ll need a work surface to assemble the parts on before installing ...

  • Page 4

    2 faststor rack mount installation instructions 62-0125-01 unpacking the rackmount kit refer to the illustration below while performing the steps that follow: 1. Open the shipping carton and remove the square cardboard tube from the inner tray. Set the cardboard tube on the work surface. 2. Remove t...

  • Page 5

    62-0125-01 faststor rack mount installation instructions 3 9. Verify that you have the components listed in the following table: faststor rackmount kit components component id description quantity 1 support box with attached inner slide rail 1 2 cover, top, support box 1 3 screw, panhead, slotted, 8...

  • Page 6

    4 faststor rack mount installation instructions 62-0125-01 preparing the rack refer to the following illustration while performing steps 1and 2: 1. Verify the alignment of the ends of the two front slide/rail assemblies (#13). The front edge of the slide rail should be aligned with the notch in the ...

  • Page 7

    62-0125-01 faststor rack mount installation instructions 5 refer to the following illustration while performing steps 3 and 4: 3. Mount each slide rail assembly to your rack using four philips, panhead screws (#10) and a nut plate (#11) to secure them to the rack’s vertical mounting-rails. Note that...

  • Page 8

    6 faststor rack mount installation instructions 62-0125-01 preparing a single faststor for rack mounting determining model the first step in the rack mounting process is to determine the model of your faststor. The following two illustrations represent different models of a rack-mountable faststor. ...

  • Page 9

    62-0125-01 faststor rack mount installation instructions 7 installing kit components 1. Mount the left-hand inner slide rail (#15) to the faststor using two slotted, pan head screws (# 3) as shown below. Note: if the rear mounting-hole on the chassis is not threaded, you have an early rack-ready mod...

  • Page 10: Rack Mounting Dual Faststors

    8 faststor rack mount installation instructions 62-0125-01 rack mounting dual faststors these instructions provide detailed descriptions of the steps you must perform to install a pair of faststors in a single slot of your rack. You’ll need a work surface to assemble the parts on before installing y...

  • Page 11

    62-0125-01 faststor rack mount installation instructions 9 3. Using a #1 philips screwdriver, remove the two philips, panhead screws (#19) in the front and rear compartment of the support box. 4. Using a #1 philips screwdriver, remove the philips, panhead screw (#8) and kepnut (#9), in the front com...

  • Page 12

    10 faststor rack mount installation instructions 62-0125-01 3. Grasp the handle and pull the drive assembly out from the chassis. There are two screws on the bottom of the drive assembly frame that act like stops when removing the assembly. To slide the assembly past these stop points, simply lift u...

  • Page 13

    62-0125-01 faststor rack mount installation instructions 11 8. Using a #1 philips screwdriver, install the philips, panhead screw (#7) through the keyhole shaped cutout inside faststor #2 into the threaded rear mounting hole inside faststor #1. Note: if the threaded mounting hole is missing inside f...

  • Page 14

    12 faststor rack mount installation instructions 62-0125-01 11. Using a #1 philips screwdriver, install the right-hand mounting bracket (#16) to the right side of faststor #2 using two philips, panhead screws (#7). Be sure that the thumbscrews are positioned at the bottom. 12. If not already mounted...

  • Page 15

    62-0125-01 faststor rack mount installation instructions 13 installing the faststor/support box assembly into the rack 1. With an assistant, lift the faststor/support box assembly into position, and then guide the slides mounted on the faststor and support box into the slide rail assemblies on the r...

  • Page 16: Faststor

    14 faststor rack mount installation instructions 62-0125-01 appendix a: slide rail attachment for early model faststor this appendix applies only to early model faststor units with a non-threaded rear mounting-hole for the left slide rail attachment. When installing the slide rail, you will need to ...

  • Page 17

    62-0125-01 faststor rack mount installation instructions 15 3. Mount the front of the left-hand inner slide rail (#15) to your faststor at the front mounting-hole using a slotted, pan head screw (# 3). Refer to the illustration below for the location of the front mounting-hole. 4. Secure the rear of...

  • Page 18: Ready Faststor

    16 faststor rack mount installation instructions 62-0125-01 appendix b: rear mounting point for early model rack- ready faststor follow this procedure to attach an early model rack-ready faststor to another faststor. 1. Using a #1 philips screwdriver, install the philips, panhead screw (#19) into th...

  • Page 19

    62-0125-01 faststor rack mount installation instructions 17 advanced digital information corporation corporate headquarters 11431 willows road ne redmond, wa 98052 telephone: (425) 881-8004 fax: (425) 881-2296 adic europe zac des basses auges 1, rue alfred de vigny 78112 – fourqueux, france telephon...