Qvis G3-mini keyboard User Manual - Keyboard Parameter Setting
11
Success!
1 Set left limit
2 Set right limit
3 Run scan
、
、
、
Preset num:
1-255
(
)
Preset num:
1-255
(
)
Preset num:
1-255
Press prev to back
(
)
The
first item is t o s a v e t h e setting dome
preset;
the second item calls dome preset; the
third
item clears the dome preset.
Choos
e 【 1 】 to enter preset setting,
this
item requires inputting the preset
number
that you want to save, t h e LCD w i l l
d i s p l a y w h a t i s s h o w n i n Picture 4.2.1-3
After entering
the setting dome preset menu, the
joystick will control the dom e directly
. Input the
corresponding preset number, then press
Enter
to save, LCD will show (
). As picture 4.2.1-4
shows.
【
】
Success
NO TICE
After entering the c a m e r a ' s prese t menu, the
joystick w ill control the c a m e r a directly,
at this time the keys in t h e lens control
area also can control th e c a m e r a lens ,
the operation of the joystick and the
key s a r e invalid for the dome under the
general menu mode.
Input corresponding preset number, press
Enter
to call preset, LCD will show (
)
tilt the joys tick left or press
to back to the
former menu.
【
】
【
】
Success
P rev
Press
3
to enter the clearing preset menu,
As LCD shows (Picture 4.2.1-6)
【 】
Input the preset num ber that you want to clear,
) and g o back to the former menu.
press
【 E N T E R 】 clear preset, LCD will show
(Success
Pictu re 4.2.1-6
Picture 4. 2.1-5
Picture 4.2 .1-4
4.2 .2 Dome scan setting
Enter the menu, as LCD shows (picture 4.1.1-1)
Press
to enter the dome setting menu, as
LCD shows (picture4.2.1-1)
Press
again to enter the dome scan setting
menu, as LCD shows (picture4.2.2-1)
【 】
【 】
2
2
Dome scan setting
includes setting dome left li-
mit, right limit
and running scan.
Choos
e 【 1 】 to set dome left limit, as LCD
s
hows (Picture 4.2.2-2)
Pictu re 4.2.1-3
Picture 4.2.2-1
Keyboard Parameter Setting
4. 2 Dome setting
1 Set dome preset
2 Set dome scan
3 Set dome pattern
4 Set dome tour
、
、
、
、
1 Save preset
2 Show preset
3 Clear preset
、
、
、
4.2.1 Dome preset setting
En ter the m a in m e nu, a s L CD sh ow s
t h e
f o l l o w i n g (Picture 4.1.1-1)
Pr e ss
【
2 】 to enter dome setting menu, as
L CD
shows t h e f o l l o w i n g (Picture 4.2.1-1);
m o ve
joystick up and down to separately set
t
h e dome preset, scan, pattern and tour.
Press
【
1 】 to enter dome preset setting,
a s
LCD shows i n (Picture4.2.1-1).
Picture 4.2.1-1
Picture 4.2.1-2
You will need to refer to the matrix and PTZ
camera/dome manuals to help complete the
setup using the keyboard. Some parameters to
be set my differ depending on the camera/dome
used.
Press
【PREV】to go back to the former menu.
Press '2' to enter the calling preset menu, the LCD will
display the following as shown in Picture 4.2.1-5.