Qvis G3-mini keyboard User Manual - Keyboard Parameter Setting
12
1 Tour num:
2 Insert preset
3 Run tour
、
_
、
、
Picture 4.2.3-2
Press 1 to start
Press prev to back
Press 0 to stop
A fter entering the
menu, the system requires y o u
t o input t h e pattern tour that you set in the first
item, the
input range is 1-4, press
【Enter】 to
confirm,the c ursor will auto-jump
to the second
item
. To start setting a pattern ( if user has
finished to set pattern
already you can jump over this
item) choose
【3】to run pattern directly.
Pattern setting: after enter ing
the pattern menu,
to move the dome
in an appropriate position, press
to start to record pattern tour. LCD will show
(
) as pic ture 4.2.3-2 shows.
Start......
【 】
1
Press (0) to stop recording pattern, LCD will show
(
) and
w i l l g o back to the former menu,
it means the operation w a s successful.
Success
N OTICE
After entering the setting c a m e r a pattern
menu, the joystick will control the dome
directly, at this time the keys in lens
controlling area also can control the dome
lens, the operation of the joystick and the key
is invalid for the dome under general menu
mode.
Press
to enter dome setting m enu, as LCD
shows (picture 4.2.1-1)
Then Press
4
to enter the menu of tour, as
LCD shows (pictur e
4.2.4-1)
【 】
【 】
2
4.2.4 Tour setting
After entering the menu, the system requires
y o u
t o input t h e tour that you will set in the first item , the
input
range is 1-6, press
【Enter】 to confirm, the
cursor will
auto-jump to the second row to start tour
setting, if
user has finished to set tour already, you
can
jump over the second item to run t h e tour
directly,
t h e LCD will show '
Success' and back to
the
former menu, it means the operation is
successful.
Choos
e the second item (as picture 4.2.4-2
shows)
to input presets that you need to insert in
a tour
. Inputting a preset speed in the second item:
Input
range i s b e t w e e n 1-127. Input t h e preset
par
k time in the third item:input range between 1-255
Press
【Enter】 to confirm, LCD will show
Success and w i l l g o back to the former
menu
, it means the operation of adding preset is
successful.
Picture 4.2.4-1
1 Preset num:
2 speed:
3 dwell:
、
_
、
、
Press
3
to run tour.
【 】
Pictu re 4.2.4-2
Keyboard Parameter Setting
N OTICE
It is valid to insert the presets in tou r under
theVIDO-B02 protocol but it is invalid
under other protocols.
Press enter sure
Press prev to back
1 Pattern num:
2 Set pattern
3 Run pattern
、
_
、
、
A fter entering the
setting dome limit menu, to
move the
dome in an appropriate position, then
press
Enter
to save, LCD will show (
)
and
w i l l g o back to the former menu.
【
】
Success
Choos
e the second item (Set right limit), i t i s
t h e same operation w h e n s e t t i n g left limit.
Back to scan menu, then press
3
to run scan.
【 】
After entering the c a m e r a limit s e t u p
menu, the joystick will control the c a m e r a
directly, at this time the keys in t h e
lens c ontrol area c a n also control the
c a m e r a lens , the operation of the
joystick and the ke y s a r e invalid for
the c a m e r a under the general menu .
NOT ICE
4.2.3 Pattern setting
Enter the menu, as LCD shows (picture 4.1.1-1)
Press
2
to enter the dome setting menu, as
LCD shows (Picture 4.2.1-1)
Then Pres s
3
to enter the pattern setting
menu, as LCD shows (picture 4.2.3-1)
【 】
【 】
Picture 4.2.2-2
Picture 4.2.3-1