- DL manuals
- RAMSET
- Power Tool
- GYPFAST
- Instruction Manual
RAMSET GYPFAST Instruction Manual
Summary of GYPFAST
Page 1
Ramset gypfast operator’s safety & operating instruction manual danger read and obey all safety and operating instructions before operating tool. Gas powered, low velocity piston type fastening tool.
Page 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 an overview of the gypfast tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 3
Description the gypfast tool is a self-contained, fully portable tool that uses liquid hydrocarbon fuel to power a unique linear drive internal combustion motor . In order for you to fully understand the information contained in this manual, you need a basic under- standing of the tool . As you can ...
Page 4: Safety Instructions
Safety instructions safety instructions 4 the following safety instructions have been included in this manual to provide you with basic information necessary for safe operation of the gypfast tool . Do not attempt to operate this tool until you read and understand all safety precautions and manual i...
Page 5: Safety Instructions
5. Never carry the tool with your finger on, or depressing, the trigger. You must remember that the gypfast tool operates in a specific sequence . The safety yoke acts as an operating feature that blocks the trigger from completing the ignition circuit . Should you unintentionally depress the safety...
Page 6: Safety Instructions
14. Never carry fasteners or other hard objects in the same pocket or container with fuel cell. The fuel cell could be punctured, causing serious injury . 15. Never allow anyone to use the gypfast tool unless they read and understand the tool manual and all safety instructions. It is the tool owner’...
Page 7
Battery and charger the first step in preparing a new tool for operation is to fully charge the new battery . New batteries are shipped discharged and must be charged for 24 hours before first use . All subsequent charges will require at most a 3 hour charge . Warning important charging notes chemic...
Page 8
The battery and charging system the battery and charging system 8 inserting battery 1 . Load the battery, terminals first, into the gypfast tool . 2 . Make sure it is securely locked into place . Battery indicator light the illustration is a closeup of the side of the gypfast tool . On the side of t...
Page 9
Fuel cell and metering valve 9 fuel cell and metering valve fuel cell danger explosion/fire hazard read all safety instructions before using or handling the fuel cell . Failure to follow all instructions may result in explosion or fire . This may cause severe personal injuries or property damage . K...
Page 10
Fuel cell and metering valve fuel cell and metering valve 10 inserting fuel cell with the metering valve stem pointed toward the front of the tool, insert the metering valve/fuel cell assembly . As you slide the metering valve/fuel cell assembly into the gypfast tool, you will notice that there is a...
Page 11
Fasteners the gypfast tool can drive only itw ramset fasteners . Any other fastener will cause tool damage and void your warranty . Loading and unloading fasteners 1 . Lay the tool on its right side, exposing the gate latch . 2 . Unlatch and open the gate . Swing open the magazine cover . 3 . Comple...
Page 12: Servicing
Servicing servicing 12 field service should be restricted to the following: q checking the energy level of the battery q recharging the battery q checking the fuel cell and metering valve q replacing the fuel cell q cleaning the air filters q clearing a jam attempts to go beyond these procedures cou...
Page 13: Servicing / Maintenance
Servicing / maintenance 13 servicing /maintenance clearing a jam a typical problem you may encounter is having a jammed fastener . Because of the unique design of the gypfast tool, clearing a jammed fastener is easy . Damage to parts and/or excessive accumulation of dirt are principle causes of jams...
Page 14: Maintenance
Maintenance 14 maintenance end-of-workday routine at the end of each workday, conduct an end-of- workday routine . These simple steps are based on maintaining the safety and operational efficiency of the gypfast tool . Before you leave the worksite: 1 . Remove the battery and store in the tool case ...
Page 15: Troubleshooting
Symptom possible problems service preparing tool for operation—battery/charger problems normal stage of operation pre-combustion/combustion stage of operation — fan does not run —tool led is off . — fan does not run, or runs slower than normal —tool led is red . — battery is not charged . — battery ...
Page 16: Troubleshooting
Symptom possible problems service power/exhaust stage of operation returning/purging stage of operation if the gypfast tool will not operate after following the above service directions, return the tool to an ramset distributor sales representative for service. 800-241-5640 www.Ramset.Com — battery ...
Page 17: Warranty
Ramset warrants that new gypfast systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below. Two-year/50,000 shot warranty a two-year/50,000 shot warranty, which ever comes first, will apply to all parts, except those listed ...
Page 18
For tool repair service contact your local authorized ramset distributor or to find your nearest ramset tool repair center visit our web site at www.Ramset.Com or call 800-241-5640 concrete fastening systems glendale heights, il 60139 800-ramset6 (1-800-726-7386) www.Ramset.Com buy with confidence.....