Ramset t2 tool operators safety & operating instruction manual danger read and obey all safety and operating instructions before operating tool. Gas powered, low velocity piston type fastening tool.
Safety introduction danger safety introduction danger 2 ! Read, understand and follow the instructions in the tool manual before attempting to use the tool. ! Operators and bystanders must wear eye and hearing protection. ! Never close tool with hand over the fastener loading end of the tool. A seri...
Safety introduction 2 contents 3 safety instructions 4-7 fastening applications 8 tool operating instructions 9 parts schematic 10-11 parts list 12-13 servicing/troubleshooting 14 warranty 15 table of contents table of contents 3.
Preparation for fastening acceptable base materials the gas powered t2 tool is suitable for use in the following base materials only: • pouredconcrete • structuralsteel • concreteblockandhorizontaljoints in brick or masonry walls never attempt to fasten into any other type of material. Fastening int...
Fuel cells and batteries fuel cells • thefuelcellmustbeusedat temperatures between -5° c (23° f) and 49° c (120° f). • atthebeginningofeachfastening cycle, a measured amount of gas is injected into the combustion chamber. • thefuelcellisdesignedwithan internal reservoir that is under pressure by a p...
Installing the battery • insertthebatteryintothetool as shown on the right with the clip toward the rear. • notetheledlightontheright side of the handle. After installing the battery: - if the light flashes green the tool is powered. - if the light flashes red the battery requires charging. - if the...
Failure to follow instructions can cause injury to the tool operator or to bystanders. • usethetoolonlyinwellventilated areas. • alwaysholdthetoolatrightangles to the work surface. • neverattempttomakeafastening at an angle to the work surface. • whilethetoolcanbeusedinany position (floor, wall or c...
Fastening applications your t2 tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well as help you perform these fastening operations safel...
Tool operation always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fastener. Operating the t2 tool 1. Insert a charged battery into the too...
Ramset t2 tool schematic parts schematic 10 parts schematic.
Ramset t2 tool schematic (continued) parts schematic 11 parts schematic.
Ramset t2 tool parts lists key part number description 1 336920 grill cap 2 336900 air filter 3 b0060a cap screws m5-30 w/washer 4 339000 cap assembly 5 b0070 spark plug wire 6 b0061a pc board screws, m4-12 7 b0040 pc board 8 7505164 spark plug assembly 9 900525a fan motor assembly (includes fan, mo...
Parts list 13 parts list ramset t2 tool parts lists (continued) key part number description 37 334020 battery support 38 337440 rubber handle grip 39 333380 knob assembly 40 404619 insulator 41 404490 trigger switch 42 404385 light conduit 43 b0134 spark unit assembly, mefi-r 45 010422 efi junction ...
Filters and battery contacts cleaning the filters and battery contacts on a regular basis will help make your tool work more efficiently. To clean the filters • remove the cover and the filters. • lightly tap the filters to remove any dust. • replace the filters if damaged. • replace the filters and...
Ramset warranty that new t2 power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below, after the date of delivery to the original user. Two-year warranty a two-year warranty will apply to all parts, except those listed below as norm...
For tool repair service contact your local authorized ramset distributor or to find your nearest ramset tool repair center visit our web site at www.Ramset.Com or call 800-241-5640 concrete fastening systems glendale heights, il 60139 800-ramset6 (1-800-726-7386) www.Ramset.Com buy with confidence.....
