Rapid 2005 Installation, operation & service manual - Warning
B-S
ERIES
I
NSTALLATION
, O
PERATION
AND
S
ERVICE
M
ANUAL
24 of 147
SECTION 9: LEGS
Part n
u
mbers that end
w
ith a “[W]” indicate that the
part can be ordered
w
ith either an
u
npainted
gal
v
anized finish or an acrylic modified alkyd enamel
finish. To order
w
ith a gal
v
anized finish, do not
incl
u
de the "W" at the end of the part n
u
mber; to
order
w
ith a painted finish, incl
u
de the "W" at the end
of the part n
u
mber.
9.1 Le
g
Mountin
g
Legs can be
u
sed
w
hen mo
u
nting an air handler on a
concrete slab or directly on the floor. Legs are
a
v
ailable for all models in the horizontal
config
u
ration.
9.2 Le
g
Mountin
g
- Horizontal Air Handler
(2005 - 2030)
The 46" (116.8 cm) legs m
u
st first be mo
u
nted to the
air handler before being mo
u
nted to the concrete
slab or floor. To attach the legs
w
ith the air handler
m
u
st first be lifted
w
ith the pro
v
ided lifting l
u
gs.
for safe lifting practices. In each
corner of the bottom of the air handler, fo
u
r leg-
mo
u
nting holes
w
ill be fo
u
nd.
.
The legs can no
w
be mo
u
nted one at a time to the
inside of the corner by remo
v
ing the hard
w
are that
occ
u
pies each of the bolt locations. Place the leg on
the inside of the corner and attach
w
ith the pre
v
io
u
sly
remo
v
ed hard
w
are. Missing hard
w
are needs to be
added at each bolt location. The req
u
ired hard
w
are is
a 5/16"-18 x 1" grade 5 bolt, a 5/16" flat
w
asher, and
a 5/16"-18 grade 5 flange n
u
t.
On models 2020 and 2030, there is a bracket on the
inside of each corner that is held in place by the t
w
o
bolts closest to the corner. This bracket m
u
st be
remo
v
ed
w
hen the leg is attached to the air handler.
Bracket can be discarded once legs are attached.
FIGURE 17: Le
g
Mountin
g
Holes (2005 - 2030)
To attach the legs to a concrete slab, the base of
each leg is eq
u
ipped
w
ith t
w
o 1" holes. St
u
ds
capable of accepting 5/8" n
u
ts m
u
st be installed in
the concrete slab. For st
u
d positioning,
.
The air handler may no
w
be placed do
w
n o
v
er the
slab st
u
ds. The legs sho
u
ld then be bolted do
w
n
w
ith
5/8" n
u
ts.
.
Crush Hazard
Use proper lifting
equipment and
practices.
Falling Hazard
Use proper safety
equipment and prac-
tices to avoid falling.
Severe Injury Hazard
Use proper lifting
practices and equip-
ment.
Equipment and
accessories are
heavy.
Cut/Pinch Hazard
Wear protective gear
during installation,
operation and
service.
Edges are sharp.
WARNING
Failure to follow these instructions can result in death, injury or property damage.
10"
(25.4 cm)
1.5"
(3.
8
cm)
1.5"
(3.
8
cm)
10"
(25.4 cm)