Raptor HAWK216OEM1 Instruction Manual - page 12
HAWK216 Instruction Manual
Document number
Revision
File name
Date
Page
2013-12-11-01
V1.1
HAWK216OEM1_IM_v1_1
19-Aug-14
12 of 19
4.3
Set Commands
Set Command
Serial Packet
Comments
Set system state
0x4F 0xYY 0x50
YY Bit 6= 1 to enable check sum mode
YY Bit 4 = 1 to enable command ack
YY Bit 1 = 0 to Hold FPGA in RESET
YY Bit 0 = 1 to enable EEPROM comms
YY Bits 2,3,5,7 = reserved
Set FPGA CTRL reg
0x53 0xE0 0x02 0x00 0xYY 0x50
YY Bit 0 - 1=TEC ON (Default=1)
YY Bit 1 - unused
YY Bit 2 - unused
YY Bit 3 - 1 = AGC ON (Default=1)
YY Bit 4 - unused
YY Bit 5 - unused
YY Bit 6 - unused
YY Bit 7 - unused
Set AGC Auto level
0x53 0xE0 0x02 0x23 0xMM 0x50
0x53 0xE0 0x02 0x24 0xLL 0x50
10 bit value
– max 0x012B = White
MM bits 1..0 = level bits 9..8
LL = level bits 7..0
(default = 0x012B)
Set AGC PEAK/Average
Ration
0x53 0xE0 0x02 0x2D 0xYY 0x50
YY 8-bit value
0 = Full Peak
255 = Full Average
(default = 0x7F)
Set AGC speed
0x53 0xE0 0x02 0x2F 0xYY 0x50
YY Bits 7..4 = EM speed(Default=F)
YY Bits 3..0 = EXP speed(Default=F)
Set EM gain
(AGC must be disabled)
0x53 0xE0 0x02 0x15 0x0L 0x50
0x53 0xE0 0x02 0x16 0xMM 0x50
Never exceed the EM Gain Maximum
stored in the EEPROM.
12 bit word;
L = 4 MSBs (Upper nibble)
MM = 8 LSBs
Set TEC Target
temperature
0x53 0xE0 0x02 0x1A 0x0L 0x50
0x53 0xE0 0x02 0x1B 0xMM 0x50
12 bit word;
L = 4 MSBs (Upper nibble)
MM = 8 LSBs
Set TEST PATTERN
0x53 0xE0 0x02 0xFA 0xYY 0x50
YY Bit 7= 1 Gamma Enabled (Default)
YY Bit 7= 0 Gamma Disabled
YY Bit 6= 1 Trigger Out Enabled (Default)
YY Bit 6= 0 Trigger Out Disabled
Bit 3 Bit 2 Bit 1 Bit0 (of YY)
0 0 0 0 Normal(Default)
0 0 0 1 Incrementing TP
0 0 1 0 Full White
0 0 1 1 ½ White
0 1 0 0 ¼ White
0 1 0 1 Const. 64
0 1 1 0 Const. 128
0 1 1 1 Const. 256
1 0 0 0 Black
1 0 0 1 Vert Stripes