Raptor HAWK216OEM1 Instruction Manual - page 13
HAWK216 Instruction Manual
Document number
Revision
File name
Date
Page
2013-12-11-01
V1.1
HAWK216OEM1_IM_v1_1
19-Aug-14
13 of 19
4.4
Query Commands
Query Command
Send Serial Packet
Comments
Get system status
0x49 0x50
1 Byte returned
YY Bit 6= 1 Check sum mode enabled
YY Bit 4 = 1 Command acknowledge enabled
YY Bit 1 = 0 Hold FPGA in RESET
YY Bit 0 = 1 EEPROM enabled
YY Bits 2,3,5,7 = reserved
Get FPGA CTRL reg
0x53 0xE0 0x01 0x00 0x50
0x53 0xE1 0x01 0x50
YY Bit 0 - 1=TEC ON (Default=0)
YY Bit 1 - unused
YY Bit 2 - unused
YY Bit 3 - 1 = AGC ON (Default=1)
YY Bit 4 - unused
YY Bit 5 - unused
YY Bit 6 - unused
YY Bit 7 - unused
Get AGC Auto level
0x53 0xE0 0x01 0x23 0x50
0x53 0xE1 0x01 0x50
0x53 0xE0 0x01 0x24 0x50
0x53 0xE1 0x01 0x50
2 bytes returned MM,LL - 10 bit value
0M bits 1..0 = level bits 9..8
LL = level bits 7..0
Get PEAK/Average
setting
0x53 0xE0 0x01 0x2D 0x50
0x53 0xE1 0x01 0x50
YY 8-bit value
0 = Full Peak
255 = Full Average
Get AGC speed
0x53 0xE0 0x01 0x2F 0x50
0x53 0xE1 0x01 0x50
YY Bits 7..4 = EM speed(Default=7)
YY Bits 3..0 = not used
Get EM gain Maximum
0x53 0xE0 0x01 0x35 0x50
0x53 0xE1 0x01 0x50
0x53 0xE0 0x01 0x36 0x50
0x53 0xE1 0x01 0x50
2 bytes returned 0M,LL
– 12 bit word
0M = 4 MSBs
LL = 8 LSBs
Get EM gain
0x53 0xE0 0x01 0x15 0x50
0x53 0xE1 0x01 0x50
0x53 0xE0 0x01 0x16 0x50
0x53 0xE1 0x01 0x50
2 bytes returned 0M,LL
– 12 bit word
0M = 4 MSBs
LL = 8 LSBs
Get TEC Target
Temperature
0x53 0xE0 0x01 0x1A 0x50
0x53 0xE1 0x01 0x50
0x53 0xE0 0x01 0x1B 0x50
0x53 0xE1 0x01 0x50
2 bytes returned 0M,LL
– 12 bit word
0M = 4 MSBs
LL = 8 LSBs
Get TEST PATTERN
state
0x53 0xE0 0x01 0xFA 0x50
0x53 0xE1 0x01 0x50
1 byte returned
YY Bit 7= 1 Gamma Enabled (Default)
YY Bit 7= 0 Gamma Disabled
YY Bit 6= 1 Trigger Out Enabled (Default)
YY Bit 6= 0 Trigger Out Disabled
Bit 3 Bit 2 Bit 1 Bit0 (of YY)
0 0 0 0 Normal(Default)
0 0 0 1 Incrementing TP
0 0 1 0 Full White
0 0 1 1 ½ White
0 1 0 0 ¼ White
0 1 0 1 Const. 64