Rayburn Heatranger 480CD User Instructions

Other manuals for Heatranger 480CD: Installation Instructions Manual

Summary of Heatranger 480CD

  • Page 1

    12/15 eopi 514711 for use in gb and ie users instructions desn 514712 please read these instructions before using this appliance raywarranty@aga-web.Co.Uk rayburn 480cd.

  • Page 2: Contents

    Contents section page introduction 3 user information 3 controls 4 the cooker 5 cooking hints 6 the boiler 7 the programmer 7 - 9 cleaning and caring for your cooker 10 burner re-set 11 gas leak or fault 11 power failure 11 servicing 11 2 note: smoke/smell emitted during initial usage some parts of ...

  • Page 3

    3 user information thank you for buying a rayburn appliance. To get the best from it, please read this leaflet and abide by the warnings, carefully follow the instructions before using your rayburn for the first time. Consumer protection as responsible manufacturers we take care to make sure that ou...

  • Page 4

    4 controls fig. 1 desn 514713 mark approx temp low 250°c 240°c 230°c 220°c 200°c 190°c 180°c 160°c 140°c 150°c 120°c 1 2 3 4 5 6 7 8 9 high.

  • Page 5

    Mark shelf approximate time scones 7 (220°c) 3 10 - 15 mins small cakes 5 (190°c) 4 15 - 20 mins (turn the tray round halfway through cooking. For best results place the solid plain shelf on the top runner) victoria sandwich 4 (180°c) 3 + 5 20 - 30 mins (move the lower cake up when the top cake is c...

  • Page 6

    6 the ovens are indirectly heated from the outside by hot gases from the heat source so that no flame or elements are within the ovens. This means that full use can be made of the whole cooking space. Both ovens are vented, so cooking smells disappear to the outside, but please make sure that the ve...

  • Page 7

    The temperature of the water produced can be adjusted by means of the boiler thermostat control knob. This knob can also be used to turn the boiler off. The boiler knob is situated behind the control door (see fig. 1). For safety purposes an overheat and flow sensor are fitted. These are safety cut-...

  • Page 8

    1. Ensure that the auto mode is being used when setting the programmer. 2. Press the set button twice. 3. The display should alternate between on1 and the time of day currently set. 4. Adjust to the time required by using + or - buttons to set time you wish cooker to turn on (e.G. Morning). 5. Press...

  • Page 9

    1. To set individual days, press set once. 2. Adjust to the day required using + or - buttons. 3. Press set to confirm the day chosen. 4. Adjust to the new times required as before. 5. Again, if an event is not needed set to 00:00. 6. Once day is set (both events), display should default to time of ...

  • Page 10

    Cleaning and caring for the cooker 10 remember: be careful of the hot appliance. Do not use a steam cleaner to clean this cooker. Rayburn enamel cleaner and rayburn chrome & stainless steel cleaner are recommended. Enamelled top plate and front plate l to keep the vitreous enamelled surface bright a...

  • Page 11

    If a fault occurs on either burner then a fault code is displayed and shuts down the part of the appliance with a fault (cooker or boiler). This can be re-set after 1 minute, by pressing the repeat button. In the event of repeated failure switch off the gas and electrical supply to the appliance and...

  • Page 12

    12 for further advice or information contact your local distributor/stockist with aga rangemaster’s policy of continuous product improvement, the company reserves the right to change specifications and make modifications to the appliance described at any time. Manufactured by aga rangemaster station...